How to Replace a Delta Bathtub Faucet: A Step-by-Step Guide

AvatarByLiana Farrell Faucet Queries

How to Replace a Delta Bathtub Faucet

Your bathtub faucet is one of the most used fixtures in your home, so it’s important to keep it in good working order. If your faucet is leaking, dripping, or not working properly, it’s time to replace it. Replacing a Delta bathtub faucet is a relatively simple DIY project that can be completed in about an hour.

In this article, we’ll walk you through the steps of replacing a Delta bathtub faucet, from start to finish. We’ll provide detailed instructions and images to help you along the way. So if you’re ready to take on this project, read on!

Step Instructions Image
1 Turn off the water supply to the faucet.
2 Remove the old faucet by unscrewing the nuts that hold it in place.
3 Install the new faucet by screwing it into place and tightening the nuts.
4 Turn on the water supply and test the faucet to make sure it is working properly.

How to Replace a Delta Bathtub Faucet

A bathtub faucet is a critical part of your bathroom, and it’s important to keep it in good working order. If your bathtub faucet is leaking, dripping, or not working properly, it’s time to replace it. Replacing a Delta bathtub faucet is a relatively simple DIY project that can be completed in a few hours.

In this guide, we will walk you through the steps of replacing a Delta bathtub faucet. We’ll provide detailed instructions and photos, so you can be confident that you’re doing the job correctly.

Gather the necessary tools and materials

Before you begin, gather the necessary tools and materials. You will need:

  • Replacement Delta bathtub faucet
  • Adjustable wrench
  • Penetrating oil
  • Pliers
  • Tape measure
  • Combination/socket wrench
  • Screwdriver
  • Plumber’s putty
  • New washers and O-rings
  • Rags

Shut off the water supply

The first step is to shut off the water supply to the bathtub faucet. To do this, turn off the main water supply to the house. This is usually located near the water meter.

Once the main water supply is turned off, locate the shut-off valves for the bathtub faucet. These valves are usually located behind the faucet or under the sink. Turn the shut-off valves clockwise to stop the flow of water.

Remove the old faucet

Now that the water supply is turned off, you can begin to remove the old faucet. Start by removing the escutcheon plate. This is the decorative cover that surrounds the faucet. The escutcheon plate is usually held in place by two screws. Remove the screws and set the escutcheon plate aside.

Next, remove the faucet handles. The handles are usually held in place by a setscrew. Use a screwdriver to loosen the setscrew and remove the handles.

Now you can begin to remove the faucet body. The faucet body is held in place by two bolts. Locate the bolts and use a wrench to loosen them. Once the bolts are loosened, you can remove the faucet body.

Install the new faucet

Now you can install the new faucet. Start by attaching the new faucet body to the sink. The faucet body is usually attached with two bolts. Use a wrench to tighten the bolts.

Next, install the new escutcheon plate. The escutcheon plate is usually held in place by two screws. Use a screwdriver to tighten the screws.

Now you can install the new faucet handles. The handles are usually held in place by a setscrew. Use a screwdriver to tighten the setscrew.

Finally, turn on the main water supply and check for leaks. If there are no leaks, you’re done!

Replacing a Delta bathtub faucet is a relatively simple DIY project that can be completed in a few hours. By following the steps in this guide, you can be confident that you’re doing the job correctly.

Here are a few additional tips for replacing a Delta bathtub faucet:

  • Use plumber’s putty to seal around the faucet body. This will help to prevent leaks.
  • Make sure that the new faucet is compatible with your sink.
  • If you’re not comfortable doing this project yourself, you can always hire a professional plumber.

How to Replace a Delta Bathtub Faucet?

Replacing a Delta bathtub faucet is a relatively simple task that can be completed in about an hour. However, it is important to follow the steps carefully to ensure that the new faucet is installed correctly and that you do not damage the existing plumbing.

Tools and materials:

  • New Delta bathtub faucet
  • Adjustable wrench
  • Penetrating oil
  • Pliers
  • Pipe wrench
  • Plumber’s putty
  • Tape measure
  • Level
  • Silicone sealant

Step 1: Shut off the water supply

The first step is to shut off the water supply to the bathtub faucet. This can usually be done by turning off the main water valve located near the water heater. Once the water supply is turned off, you can begin removing the old faucet.

Step 2: Remove the old faucet handles

The next step is to remove the old faucet handles. To do this, you will need to use a pair of pliers to grip the handle and turn it counterclockwise. Once the handle is loose, you can pull it straight off of the faucet. Repeat this process for the other handle.

Step 3: Remove the old faucet mounting nuts

The next step is to remove the old faucet mounting nuts. These nuts are located behind the faucet handles and are held in place by a set screw. To remove the nuts, you will need to use a wrench to loosen the set screw. Once the set screw is loose, you can use a pair of pliers to grip the nuts and turn them counterclockwise. Once the nuts are loose, you can pull them straight off of the faucet.

Step 4: Remove the old faucet body

The next step is to remove the old faucet body. To do this, you will need to use a pipe wrench to grip the faucet body and turn it counterclockwise. Once the faucet body is loose, you can pull it straight off of the faucet.

Step 5: Clean the faucet mounting surfaces

The next step is to clean the faucet mounting surfaces. This will help to ensure that the new faucet seals properly. To clean the surfaces, you can use a rag and some rubbing alcohol.

Step 6: Apply plumber’s putty to the threads of the new faucet body

The next step is to apply plumber’s putty to the threads of the new faucet body. This will help to create a seal between the faucet body and the plumbing.

Step 7: Install the new faucet body

The next step is to install the new faucet body. To do this, you will need to align the faucet body with the plumbing and then turn it clockwise until it is snug.

Step 8: Install the new faucet mounting nuts

The next step is to install the new faucet mounting nuts. To do this, you will need to align the nuts with the faucet body and then turn them clockwise until they are snug.

Step 9: Install the new faucet handles

The next step is to install the new faucet handles. To do this, you will need to align the handles with the faucet body and then turn them clockwise until they are snug.

Step 10: Turn on the water supply and check for leaks

The final step is to turn on the water supply and check for leaks. If there are any leaks, you can tighten the faucet mounting nuts or apply more plumber’s putty.

Replacing a Delta bathtub faucet is a relatively simple task that can be completed in about an hour. However, it is important to follow the steps carefully to ensure that the new faucet is installed correctly and that you do not damage the existing plumbing.

If you are not comfortable completing this task yourself, you can always hire a professional plumber to do it for you.

How do I remove the old faucet?

1. Turn off the water supply to the faucet. This is usually done by turning the shut-off valves located under the sink.
2. Remove the drain cover from the bathtub. This is usually held in place by a screw or nut.
3. Disconnect the water supply lines from the faucet. There will be one line for hot water and one for cold water.
4. Remove the mounting nuts that hold the faucet to the sink. These are usually located on the underside of the faucet.
5. Lift the faucet off of the sink.

How do I install the new faucet?

1. Place the new faucet in the mounting holes in the sink.
2. Secure the faucet to the sink with the mounting nuts.
3. Connect the water supply lines to the faucet.
4. Turn on the water supply to the faucet and check for leaks.

What tools do I need?

You will need the following tools to replace a Delta bathtub faucet:

  • A screwdriver
  • A wrench
  • A pair of pliers
  • A bucket
  • A wet/dry vacuum

How long does it take to replace a Delta bathtub faucet?

The average time to replace a Delta bathtub faucet is about 30 minutes. However, this time may vary depending on the specific faucet and your level of experience.

What is the best way to prevent leaks when replacing a Delta bathtub faucet?

The best way to prevent leaks when replacing a Delta bathtub faucet is to make sure that all of the connections are tight. You should also use a sealant around the threads of the water supply lines to prevent leaks.

What are some common problems with Delta bathtub faucets?

Some common problems with Delta bathtub faucets include:

  • Leaks from the faucet body or spout
  • Dripping from the faucet handle
  • Difficulty turning the faucet on or off
  • Aerators that become clogged

How can I fix a Delta bathtub faucet that is leaking?

If your Delta bathtub faucet is leaking, you can try to fix it yourself by following these steps:

1. Turn off the water supply to the faucet.
2. Remove the faucet handle.
3. Inspect the faucet body for leaks. If you see any leaks, tighten the connections or replace the O-rings.
4. Reattach the faucet handle.
5. Turn on the water supply to the faucet and check for leaks.

If you are unable to fix the leak yourself, you should contact a qualified plumber.

How can I prevent a Delta bathtub faucet from dripping?

There are a few things you can do to prevent a Delta bathtub faucet from dripping:

  • Make sure that the faucet is turned off completely when not in use.
  • Clean the aerator regularly to prevent it from becoming clogged.
  • Replace the O-rings on the faucet if they are worn or damaged.
  • Tighten the connections on the faucet to prevent leaks.

    In this blog post, we have discussed how to replace a Delta bathtub faucet. We have provided step-by-step instructions, as well as tips and tricks to help you get the job done correctly. We hope that this information has been helpful, and that you are now able to replace your bathtub faucet with confidence.

Here are some key takeaways from this blog post:

  • Before you begin, make sure you have the necessary tools and materials.
  • Turn off the water supply to the faucet before you start working.
  • Remove the old faucet by unscrewing the mounting nuts and washers.
  • Install the new faucet by following the manufacturer’s instructions.
  • Turn on the water supply and test the faucet to make sure it is working properly.

We hope that you found this blog post helpful. If you have any questions, please do not hesitate to contact us.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.