How to Remove a Jacuzzi Bathtub: A Step-by-Step Guide

AvatarByLiana Farrell Bathtub Queries

How to Remove a Jacuzzi Bathtub

If you’re looking to replace your old Jacuzzi bathtub with a new one, you may be wondering how to remove the old one. While it’s a relatively straightforward process, there are a few things you need to know before you get started.

In this article, we’ll walk you through the steps of removing a Jacuzzi bathtub, from start to finish. We’ll cover everything from disconnecting the plumbing and electrical lines to removing the old tub itself. By the end of this article, you’ll have the knowledge and confidence to remove your old Jacuzzi bathtub yourself.

Step Instructions Images
1 Turn off the water supply to the bathtub.
2 Disconnect the drain hose from the bathtub.
3 Remove the screws that hold the bathtub to the floor.
4 Slide the bathtub out from the wall.
5 Dispose of the bathtub.

Tools and Materials Needed

To remove a Jacuzzi bathtub, you will need the following tools and materials:

  • A hacksaw
  • A reciprocating saw
  • A pry bar
  • A hammer
  • A chisel
  • A bucket
  • A wet saw
  • A shop vac
  • Safety glasses
  • Gloves
  • A respirator

Step-by-Step Instructions

1. Drain the water from the bathtub. If the bathtub is still connected to the plumbing, turn off the water supply to the bathtub and drain the water from the tub. You can do this by opening the drain plug or by using a wet vac to remove the water.
2. Remove the faucets. The faucets are usually located on the side of the bathtub. To remove the faucets, you will need to unscrew the nuts that hold them in place. You may also need to use a wrench to loosen the nuts.
3. Remove the drain assembly. The drain assembly is located at the bottom of the bathtub. To remove the drain assembly, you will need to unscrew the nuts that hold it in place. You may also need to use a wrench to loosen the nuts.
4. Cut the acrylic liner. The acrylic liner is the thin sheet of acrylic that lines the inside of the bathtub. To cut the acrylic liner, you will need to use a hacksaw or a reciprocating saw.
5. Pry the bathtub away from the wall. The bathtub is usually attached to the wall with a sealant. To pry the bathtub away from the wall, you will need to use a pry bar. You may also need to use a hammer and a chisel to help loosen the sealant.
6. Remove the bathtub. Once the bathtub is loose from the wall, you can lift it out of the bathroom. You may need to use a helper to lift the bathtub.
7. Clean up the mess. Once the bathtub is removed, you will need to clean up the mess. You can do this by sweeping up the debris and by cleaning the walls and floor.

Removing a Jacuzzi bathtub is a relatively straightforward process, but it can be a messy one. By following these steps, you can remove your Jacuzzi bathtub without any major problems.

Here are some additional tips for removing a Jacuzzi bathtub:

  • Be careful not to damage the surrounding walls or floor.
  • Wear gloves and eye protection to protect yourself from the sharp edges of the bathtub.
  • Use a shop vac to clean up the mess as you go.
  • If you are not comfortable removing the bathtub yourself, you can hire a professional to do it for you.

How To Remove A Jacuzzi Bathtub?

Removing a Jacuzzi bathtub can be a daunting task, but it is possible to do it yourself with the right tools and instructions. In this guide, we will walk you through the steps of removing a Jacuzzi bathtub, from start to finish.

1. Gather your tools and materials

Before you begin, you will need to gather the following tools and materials:

  • A hammer
  • A pry bar
  • A reciprocating saw
  • A hacksaw
  • A sawzall
  • A bucket
  • A shop vac
  • Safety glasses
  • Gloves
  • A respirator

2. Prepare the bathtub

The first step is to prepare the bathtub for removal. This involves disconnecting the water supply and drain lines, as well as removing the faucets and shower head.

To disconnect the water supply lines, you will need to find the shut-off valves located under the sink or near the water heater. Turn the valves to the off position, and then disconnect the lines from the bathtub.

To disconnect the drain line, you will need to find the P-trap under the sink. Unscrew the nuts that connect the P-trap to the drain line, and then remove the P-trap.

To remove the faucets and shower head, you will need to unscrew the nuts that connect them to the bathtub. Be careful not to damage the tiles around the faucets.

3. Remove the bathtub

Now that the bathtub is prepared, you can begin to remove it. The first step is to cut through the caulking around the bathtub. This can be done with a utility knife or a razor blade.

Once the caulking is cut, you can begin to pry the bathtub away from the wall. Use a pry bar or a hammer to gently work the bathtub loose. Be careful not to damage the tiles around the bathtub.

Once the bathtub is loose, you can use a reciprocating saw or a hacksaw to cut through the flange that connects the bathtub to the floor. Be careful not to cut through the pipes or wires underneath the bathtub.

Once the flange is cut, you can use a sawzall or a sledgehammer to break the bathtub into pieces. Be careful not to damage the subfloor or the joists underneath the bathtub.

4. Clean up the mess

Once the bathtub is removed, you will need to clean up the mess. Use a bucket and a shop vac to clean up the water and debris. Be sure to wear safety glasses and gloves to protect yourself from the dust and debris.

5. Dispose of the bathtub

The final step is to dispose of the bathtub. You can either have the bathtub hauled away by a junk removal company, or you can take it to the landfill yourself.

Safety Tips

When removing a Jacuzzi bathtub, it is important to take precautions to protect yourself from injury. Here are a few safety tips:

  • Wear safety glasses and gloves to protect your eyes and hands from the dust and debris.
  • Wear a respirator to protect your lungs from the dust and fumes.
  • Be careful not to damage the tiles around the bathtub.
  • Be careful not to cut through the pipes or wires underneath the bathtub.
  • Have a helper on hand to help you lift and move the bathtub.

Troubleshooting

If you run into any problems while removing the bathtub, here are a few troubleshooting tips:

  • If the bathtub is stuck, you can try using a heat gun or a hair dryer to loosen the caulking.
  • If the bathtub is too heavy to lift, you can try using a winch or a pulley system.
  • If you cut through a pipe or wire, you can try using a repair kit to fix the damage.

Removing a Jacuzzi bathtub can be a challenging task, but it is possible to do it yourself with the right tools and instructions. By following these steps, you can safely and successfully remove your Jacuzzi bathtub.

How do I remove a Jacuzzi bathtub?

  • Step 1: Drain the water from the bathtub. Turn off the water supply to the bathtub and open the drain. Allow all of the water to drain out.
  • Step 2: Remove the faucets. Remove the faucets by unscrewing them from the bottom of the bathtub.
  • Step 3: Remove the drain assembly. Remove the drain assembly by unscrewing it from the bottom of the bathtub.
  • Step 4: Remove the clips that hold the bathtub in place. There are usually two or three clips that hold the bathtub in place. These clips are located on the bottom of the bathtub, near the drain. Use a screwdriver to remove the clips.
  • Step 5: Lift the bathtub out of the space. Once the clips are removed, you can lift the bathtub out of the space. Be careful not to damage the bathtub or the surrounding area.
  • Step 6: Dispose of the bathtub. You can dispose of the bathtub by taking it to a recycling center or by throwing it away.

What tools do I need to remove a Jacuzzi bathtub?

You will need the following tools to remove a Jacuzzi bathtub:

  • A screwdriver
  • A wrench
  • A hammer
  • A pry bar
  • A bucket
  • A hose

How long does it take to remove a Jacuzzi bathtub?

It typically takes about 2-3 hours to remove a Jacuzzi bathtub. The exact time will vary depending on the size and condition of the bathtub.

What is the best way to remove a Jacuzzi bathtub without damaging it?

The best way to remove a Jacuzzi bathtub without damaging it is to follow the steps in the instructions carefully. Be careful not to use too much force, as this could damage the bathtub. If you are unsure how to remove the bathtub, it is best to hire a professional.

What are the risks of removing a Jacuzzi bathtub?

There are a few risks associated with removing a Jacuzzi bathtub, including:

  • Damaging the bathtub or the surrounding area
  • Getting injured
  • Creating a mess

If you are unsure how to remove the bathtub, it is best to hire a professional.

removing a Jacuzzi bathtub is a process that can be completed by a DIYer with some basic tools and know-how. However, it is important to carefully follow the steps outlined in this guide to avoid damaging the tub or the surrounding area. By taking your time and being careful, you can successfully remove your Jacuzzi bathtub and move on to a new project.

Here are some key takeaways from this guide:

  • Before you begin, make sure you have the proper tools and safety gear.
  • Carefully disconnect the water and drain lines, and remove the overflow drain.
  • Use a crowbar or pry bar to loosen the tub from the floor, and then carefully tilt it up and out of the way.
  • Patch any holes or damage to the subfloor, and then install a new bathtub.
  • By following these steps, you can successfully remove your Jacuzzi bathtub and move on to a new project.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.