How To Move A Toilet?

AvatarByLiana Farrell Toilet Queries

How to Move a Toilet

Moving a toilet may seem like a daunting task, but it’s actually a fairly simple process that can be completed in just a few steps. With the right tools and a little bit of elbow grease, you can have your toilet moved in no time.

In this article, we’ll walk you through the steps of moving a toilet, from disconnecting the water supply and sewer line to reattaching the toilet to the floor. We’ll also provide tips on how to make the process easier and more efficient.

So if you’re looking to move your toilet, read on for all the information you need.

Step Instructions Image
1 Turn off the water supply to the toilet.
2 Disconnect the water supply line from the toilet.
3 Disconnect the toilet from the floor flange.
4 Lower the toilet onto a moving dolly.
5 Move the toilet to its new location.
6 Raise the toilet onto the new floor flange.
7 Reconnect the water supply line to the toilet.
8 Turn on the water supply to the toilet.

Preparing to Move the Toilet

Before you can move a toilet, you need to prepare it by turning off the water supply, flushing the toilet, removing the toilet seat, and loosening the nuts or bolts that hold the toilet to the floor.

Turn off the water supply to the toilet. The first step is to turn off the water supply to the toilet. This is usually done by turning a valve located behind the toilet. Once the water supply is turned off, you can flush the toilet to drain the water from the tank.

Flush the toilet to drain the water from the tank. Once the water supply is turned off, you can flush the toilet to drain the water from the tank. This will help to make the toilet lighter and easier to move.

Remove the toilet seat. The next step is to remove the toilet seat. This is usually done by unscrewing the two bolts that hold the seat to the toilet. Once the bolts are removed, you can lift up on the toilet seat and pull it off.

Loosen the nuts or bolts that hold the toilet to the floor. The final step is to loosen the nuts or bolts that hold the toilet to the floor. These nuts or bolts are usually located on the back of the toilet, underneath the tank. Once the nuts or bolts are loosened, you can lift up on the toilet and slide it forward until it is free from the floor.

Place a bucket underneath the toilet to catch any water that may leak out. It is important to place a bucket underneath the toilet to catch any water that may leak out. This is because the toilet may still contain some water, even after you have flushed it.

Removing the Toilet

Once you have prepared the toilet by turning off the water supply, flushing the toilet, removing the toilet seat, and loosening the nuts or bolts that hold the toilet to the floor, you can remove the toilet.

Lift up on the toilet and slide it forward until it is free from the floor. The first step is to lift up on the toilet and slide it forward until it is free from the floor. You may need to use a pry bar or other tool to help you lift the toilet.

Carefully lower the toilet to the ground. Once the toilet is free from the floor, you can carefully lower it to the ground. Be careful not to drop the toilet, as this could damage it.

Remove the wax ring from the bottom of the toilet. The final step is to remove the wax ring from the bottom of the toilet. The wax ring is a rubber ring that creates a seal between the toilet and the floor. To remove the wax ring, you can use a utility knife or other sharp object to cut it around the edge.

Installing a New Toilet

Once you have removed the old toilet, you can install a new toilet. The process of installing a new toilet is similar to the process of removing a toilet, but in reverse.

Place the new toilet on the floor. The first step is to place the new toilet on the floor. Make sure that the toilet is centered on the drain and that the bolts are aligned with the holes in the floor.

Attach the toilet to the floor. The next step is to attach the toilet to the floor. This is done by screwing the bolts through the holes in the floor and into the bottom of the toilet.

Apply a new wax ring to the bottom of the toilet. The final step is to apply a new wax ring to the bottom of the toilet. The wax ring creates a seal between the toilet and the floor, preventing leaks.

Moving a toilet is a relatively simple task, but it is important to follow the steps carefully to avoid damaging the toilet or the floor. By following the steps in this guide, you can safely and easily move your toilet.

How to Move a Toilet?

Moving a toilet can be a daunting task, but it is possible to do it yourself with a little bit of planning and effort. Here are the steps involved in moving a toilet:

1. Preparing the Toilet for Removal

Before you can move the toilet, you need to prepare it for removal. This involves disconnecting the water supply line and the sewer line.

To disconnect the water supply line, turn off the water to the toilet at the main shutoff valve. Then, use a wrench to loosen the nut on the end of the water supply line that connects to the toilet. Be careful not to lose the washer that is located under the nut.

To disconnect the sewer line, use a plunger to push a small amount of water into the toilet bowl. This will help to loosen the wax ring that seals the toilet to the floor. Then, use a putty knife to carefully pry up the wax ring. Be careful not to damage the toilet bowl.

2. Removing the Toilet

Once the toilet is disconnected from the water supply line and the sewer line, you can begin to remove it. First, use a pry bar to loosen the bolts that hold the toilet to the floor. Be careful not to damage the floor.

Once the bolts are loosened, you can lift the toilet up and out of the way. Be careful not to drop the toilet, as this could damage it.

3. Installing the New Toilet

Once you have removed the old toilet, you can install the new toilet. Place the new toilet on the floor in the same location as the old toilet.

Apply a new wax ring to the bottom of the toilet. Align the holes in the toilet with the bolts in the floor. Insert the bolts through the holes in the toilet and tighten them.

Connect the water supply line to the toilet. Replace the toilet seat.

4. Testing the New Toilet

Once the new toilet is installed, you need to test it to make sure that it is working properly. Flush the toilet to make sure that it is flushing properly. Check for any leaks around the base of the toilet.

If you have any problems with the new toilet, you may need to call a plumber to help you fix it.

Tips for Moving a Toilet

Here are a few tips for moving a toilet:

  • Use a helper to lift the toilet. This will make the job much easier and safer.
  • Be careful not to drop the toilet, as this could damage it.
  • Protect the floor from damage by placing a piece of plywood under the toilet before you lift it.
  • If you are not comfortable moving the toilet yourself, you can hire a plumber to do it for you.

Moving a toilet can be a challenging task, but it is possible to do it yourself with a little bit of planning and effort. By following the steps in this guide, you can safely and successfully move your toilet.

How To Move A Toilet?

Q: What tools do I need to move a toilet?

A: You will need the following tools:

  • A plunger
  • A hacksaw
  • A screwdriver
  • A wrench
  • A bucket
  • A pair of gloves
  • A tarp

Q: How do I disconnect the toilet from the water supply?

A: 1. Turn off the water supply to the toilet.
2. Locate the water supply valve under the sink or toilet.
3. Turn the valve clockwise to close it.
4. Flush the toilet to drain any remaining water.

Q: How do I disconnect the toilet from the drain pipe?

A: 1. Locate the drain pipe under the toilet.
2. Use a wrench to loosen the nuts that connect the toilet to the drain pipe.
3. Be careful not to drop the nuts into the drain.

Q: How do I lift the toilet?

A: 1. Place a bucket under the toilet bowl.
2. Put on a pair of gloves.
3. Grab the toilet by the bottom and lift it up.
4. Be careful not to drop the toilet.

Q: How do I move the toilet to its new location?

A: 1. Roll the toilet on a tarp to its new location.
2. Make sure the toilet is level.
3. Connect the toilet to the water supply and drain pipe.
4. Turn on the water supply to the toilet.
5. Flush the toilet to check for leaks.

Q: How do I seal the toilet to the floor?

A: 1. Apply a bead of silicone sealant around the base of the toilet.
2. Press the toilet firmly onto the floor.
3. Allow the sealant to dry completely.

Q: What are some tips for moving a toilet?

  • Work with a friend or family member.
  • Take your time and be careful.
  • Use the right tools for the job.
  • Protect your floors from damage.
  • Be sure to turn off the water supply before you start.

    Moving a toilet is a major undertaking, but it can be done with a little planning and effort. By following the steps in this guide, you can safely and successfully move your toilet to a new location.

Here are the key takeaways from this guide:

  • Before you start, make sure you have the right tools and materials. You will need a plunger, a hacksaw, a bucket, a toilet flange, wax ring, plumber’s putty, and a new toilet seat.
  • Toilet removal is a messy job, so be sure to protect your floors and walls with plastic sheeting.
  • Turn off the water supply to the toilet and flush the toilet to drain the water from the tank.
  • Disconnect the water supply line and the drain line from the toilet.
  • Use a hacksaw to cut the bolts that hold the toilet to the floor.
  • Carefully lift the toilet off the floor and set it aside.
  • Clean the floor where the toilet was located.
  • Install a new toilet flange in the floor.
  • Apply plumber’s putty to the bottom of the new toilet.
  • Set the new toilet on the flange and attach the water supply line and drain line.
  • Turn on the water supply to the toilet and flush the toilet to test the new installation.

By following these steps, you can safely and successfully move your toilet to a new location.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.