How to Install a Shower Tub Faucet: A Step-by-Step Guide

AvatarByLiana Farrell Faucet Queries

How to Install a Shower Tub Faucet

A new shower tub faucet can be a great way to update your bathroom and improve your showering experience. But if you’ve never installed a faucet before, the process can seem daunting.

Don’t worry, it’s actually not that difficult. In this article, we’ll walk you through the steps of installing a shower tub faucet, from start to finish. We’ll provide detailed instructions and helpful tips, so you can be confident that you’ll get the job done right.

So if you’re ready to give it a try, read on!

Step Tools Instructions
1 Pliers, screwdriver, tape measure, level, pencil Turn off the water supply to the shower. Remove the old faucet by unscrewing the nuts that hold it in place.
2 Faucet parts, plumber’s putty Apply plumber’s putty to the threads of the new faucet. Insert the faucet into the hole in the wall and tighten the nuts to secure it in place.
3 Faucet handle Attach the faucet handle to the faucet body. Turn on the water supply and test the faucet to make sure it is working properly.

A shower faucet is a critical part of any bathroom, and it’s important to make sure that it’s installed correctly. If your shower faucet is leaking or not working properly, you may need to replace it. This guide will walk you through the steps of how to install a shower tub faucet.

Tools and Materials

The following tools and materials are required to install a shower tub faucet:

  • Pipe wrench
  • Adjustable wrench
  • Pliers
  • Tape measure
  • Level
  • Plumber’s putty
  • Silicone sealant
  • New shower faucet
  • New shower arm
  • Teflon tape
  • Copper washers
  • Supply lines

Preparation

Before you begin, it’s important to prepare the area around the shower drain. This will make it easier to work and will help to prevent any damage to the surrounding tiles.

To prepare the area, you will need to:

1. Turn off the water supply to the shower.
2. Disconnect the old shower faucet and shower arm.
3. Clean the area around the shower drain.

Step 1: Installing the New Shower Faucet

1. Align the new shower faucet with the existing holes in the wall.
2. Mark the location of the holes on the wall with a pencil.
3. Drill holes in the wall for the faucet.
4. Insert the copper washers into the holes in the wall.
5. Screw the shower faucet to the wall.
6. Apply plumber’s putty around the base of the shower faucet.
7. Tighten the nuts on the shower faucet until they are snug.
8. Connect the supply lines to the shower faucet.
9. Turn on the water supply to the shower and test the faucet to make sure it is working properly.

Step 2: Installing the New Shower Arm

1. Align the new shower arm with the existing hole in the shower wall.
2. Mark the location of the hole on the shower wall with a pencil.
3. Drill a hole in the shower wall for the shower arm.
4. Insert the copper washer into the hole in the shower wall.
5. Screw the shower arm to the wall.
6. Apply plumber’s putty around the base of the shower arm.
7. Tighten the nuts on the shower arm until they are snug.

Step 3: Testing the Shower Faucet

Once you have installed the new shower faucet and shower arm, it’s important to test it to make sure it is working properly.

To test the shower faucet, you will need to:

1. Turn on the water supply to the shower.
2. Turn on the shower faucet.
3. Check for leaks around the shower faucet and shower arm.
4. Adjust the temperature of the water to make sure it is comfortable.

If the shower faucet is working properly, you can enjoy your new shower!

Installing a shower tub faucet is a relatively simple task, but it is important to follow the steps carefully to ensure that it is done correctly. If you are not comfortable doing this type of work, it is best to hire a professional plumber.

3. Installation

To install a shower tub faucet, you will need the following tools and materials:

  • New shower faucet
  • New shower arm
  • Supply lines (hot and cold)
  • Pliers
  • Tape measure
  • Pencil
  • Level
  • Plumber’s putty
  • Silicone sealant
  • Rag

Install the new shower faucet.

1. Turn off the water supply to the shower.
2. Remove the old shower faucet by unscrewing the nuts that hold it in place.
3. Clean the threads on the shower valve with a rag.
4. Apply plumber’s putty to the threads of the new shower faucet.
5. Screw the new shower faucet onto the shower valve.
6. Tighten the nuts that hold the shower faucet in place.

Install the new shower arm.

1. Slide the shower arm over the shower spout.
2. Apply plumber’s putty to the threads of the shower arm.
3. Screw the shower arm onto the shower faucet.
4. Tighten the nut that holds the shower arm in place.

Connect the supply lines to the shower faucet.

1. Connect the hot and cold supply lines to the shower faucet.
2. Tighten the nuts that hold the supply lines in place.

Turn on the water supply to the shower and test the faucet.

1. Turn on the hot and cold water valves.
2. Check for leaks around the shower faucet and shower arm.
3. If there are no leaks, you have successfully installed your new shower tub faucet.

4. Final Steps

Apply plumber’s putty around the base of the shower faucet.

Plumber’s putty will help to seal the shower faucet and prevent leaks.

To apply plumber’s putty, follow these steps:

1. Apply a thin layer of plumber’s putty around the base of the shower faucet.
2. Use your fingers to smooth out the putty.
3. Let the putty dry for at least 24 hours before using the shower.

Apply silicone sealant around the shower arm.

Silicone sealant will help to protect the shower arm from rust and corrosion.

To apply silicone sealant, follow these steps:

1. Apply a thin layer of silicone sealant around the shower arm.
2. Use your fingers to smooth out the sealant.
3. Let the sealant dry for at least 24 hours before using the shower.

Wipe up any excess sealant.

Once the sealant has dried, use a rag to wipe up any excess sealant.

Installing a shower tub faucet is a relatively simple task that can be completed in a few hours. By following these steps, you can install a new shower tub faucet that will provide you with years of reliable service.

How to Install a Shower Tub Faucet?

Q: What tools do I need?

A: You will need the following tools:

  • A Phillips head screwdriver
  • A flathead screwdriver
  • A tape measure
  • A level
  • A pencil
  • A hacksaw
  • A pipe wrench
  • A plumber’s putty
  • A Teflon tape

Q: How do I prepare the area for installation?

A: First, turn off the water supply to the faucet. Then, remove the old faucet by unscrewing the nuts that hold it in place. Be careful not to damage the pipes.

Next, clean the area around the faucet with a rag and some degreaser. This will help to ensure a good seal between the new faucet and the pipes.

Q: How do I install the new faucet?

A: First, apply a bead of plumber’s putty around the base of the new faucet. This will help to create a watertight seal.

Next, insert the faucet into the hole in the wall. Make sure that the faucet is level and that the spout is in the correct position.

Once the faucet is in place, tighten the nuts that hold it in place. Be careful not to overtighten the nuts, as this could damage the faucet.

Finally, turn on the water supply to the faucet and check for leaks. If there are any leaks, tighten the nuts a little bit more.

Q: How do I adjust the water temperature and flow?

A: The water temperature and flow can be adjusted by turning the knobs on the faucet. The hot water knob is usually on the left, and the cold water knob is usually on the right.

To turn up the water temperature, turn the hot water knob clockwise. To turn down the water temperature, turn the hot water knob counterclockwise.

To turn up the water flow, turn the cold water knob clockwise. To turn down the water flow, turn the cold water knob counterclockwise.

Q: What if I have trouble installing the faucet?

A: If you have trouble installing the faucet, you can always call a professional plumber. A plumber will be able to install the faucet correctly and ensure that it is working properly.

Installing a shower tub faucet is a relatively simple task that can be completed in a few hours. By following the steps in this guide, you can easily install a new faucet that will improve the look and function of your shower.

Here are the key takeaways from this guide:

  • Before you begin, make sure you have all of the necessary tools and materials.
  • Turn off the water supply to the shower and drain the water from the pipes.
  • Remove the old faucet by unscrewing the nuts that hold it in place.
  • Clean the mounting surfaces on the shower and tub.
  • Apply plumber’s putty to the threads of the new faucet.
  • Insert the faucet into the mounting holes and tighten the nuts.
  • Connect the water supply lines to the faucet.
  • Turn on the water supply and test the faucet to make sure it is working properly.

By following these steps, you can easily install a new shower tub faucet that will improve the look and function of your shower.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.