What Size Wax Ring Do I Need for My Kohler Toilet?

AvatarByLiana Farrell Toilet Queries

Kohler toilets are known for their quality and durability, but even the best toilets can start to leak if the wax ring isn’t properly installed. A wax ring is a critical part of any toilet, as it creates a watertight seal between the toilet and the drainpipe. If the wax ring is too small or too big, it won’t create a proper seal, and water will start to leak out of the toilet.

In this article, we’ll discuss what size wax ring you need for a Kohler toilet. We’ll also provide tips on how to properly install a wax ring so that your toilet stops leaking.

Kohler Toilet Model Wax Ring Size Diameter (in)
K-3800 10″ 10.5
K-3900 12″ 12.5
K-3910 14″ 14.5

A wax ring is a ring-shaped gasket made of compressed wax that is used to seal the toilet to the floor. It prevents leaks from occurring between the toilet and the floor. Wax rings are typically made of a type of wax that is resistant to water and chemicals.

What Size Wax Ring for Kohler Toilet?

The size of the wax ring you need will depend on the size of your toilet. Kohler toilets come in a variety of sizes, so it is important to measure your toilet before you purchase a wax ring.

The most common size of wax ring for Kohler toilets is 10 inches in diameter. However, there are also smaller and larger sizes available. If you are not sure what size you need, you can always consult with a plumber.

How to Install a Wax Ring

Installing a wax ring is a relatively simple task that can be completed in a few minutes. However, it is important to follow the steps carefully to ensure that the job is done correctly.

1. Remove the old wax ring.

To remove the old wax ring, you will need to first remove the toilet from the floor. This can be done by disconnecting the water supply line and the drain line. Once the toilet is removed, you can use a putty knife to scrape off the old wax ring.

2. Clean the toilet flange.

The toilet flange is the metal ring that is attached to the floor and supports the toilet. It is important to clean the toilet flange before installing a new wax ring. You can do this by using a wire brush or a scouring pad.

3. Apply the new wax ring.

Once the toilet flange is clean, you can apply the new wax ring. The wax ring should be placed around the toilet flange with the smooth side facing up.

4. Install the toilet.

Once the wax ring is in place, you can reinstall the toilet. Be sure to tighten the bolts that secure the toilet to the floor.

5. Test the toilet.

Once the toilet is reinstalled, you should flush the toilet to test for leaks. If there are no leaks, the job is complete.

Installing a wax ring is a simple task that can be completed in a few minutes. However, it is important to follow the steps carefully to ensure that the job is done correctly. By following these steps, you can ensure that your toilet is properly sealed and that you will not have any leaks.

Additional Tips

  • If you are unsure about how to install a wax ring, you can always consult with a plumber.
  • It is important to use the correct size wax ring for your toilet. If you use a wax ring that is too small, it will not create a tight seal and you may experience leaks. If you use a wax ring that is too large, it will not fit properly and you may have difficulty installing it.
  • Be sure to clean the toilet flange before installing a new wax ring. This will help to ensure that the wax ring adheres properly and that you will not have any leaks.
  • When installing the toilet, be sure to tighten the bolts that secure the toilet to the floor. This will help to create a tight seal and prevent leaks.

What Size Wax Ring For Kohler Toilet?

The size of the wax ring you need for your Kohler toilet will depend on the diameter of the toilet drain. The most common size of wax ring for Kohler toilets is 3 1/2 inches in diameter. However, you may need a larger or smaller wax ring depending on the specific model of your toilet.

To determine the correct size of wax ring for your Kohler toilet, measure the diameter of the toilet drain. The drain is located at the bottom of the toilet bowl, and it is the hole that the water flows out of when you flush the toilet.

Once you have measured the diameter of the drain, you can purchase the appropriate size of wax ring. Wax rings are available in a variety of sizes, so you should be able to find one that fits your toilet.

How to install a wax ring on a Kohler toilet?

Installing a wax ring on a Kohler toilet is a relatively simple process. However, it is important to follow the steps carefully to ensure that the wax ring is installed correctly.

Here are the steps involved in installing a wax ring on a Kohler toilet:

1. Remove the old wax ring.

To remove the old wax ring, you will need to first remove the toilet from the floor. To do this, you will need to disconnect the water supply line to the toilet and the drain line. Once the toilet is disconnected, you can lift it up and off of the floor.

Once the toilet is off of the floor, you can remove the old wax ring. The old wax ring will be located at the bottom of the toilet bowl, and it will be held in place by a metal ring. You can use a putty knife or a utility knife to carefully pry the old wax ring out of place.

2. Apply the new wax ring.

Once the old wax ring has been removed, you can apply the new wax ring. The new wax ring will be a round, flat piece of rubber. You can apply the wax ring to the bottom of the toilet bowl using your fingers or a putty knife.

Make sure that the wax ring is applied evenly and that it covers the entire bottom of the toilet bowl. You should also make sure that the wax ring is not too thick or too thin.

3. Install the toilet.

Once the wax ring has been applied, you can install the toilet. To do this, you will need to first place the toilet on the floor. Then, you will need to connect the water supply line and the drain line. Finally, you will need to tighten the bolts that secure the toilet to the floor.

4. Flush the toilet.

Once the toilet is installed, you should flush it to make sure that the wax ring is installed correctly. If the toilet leaks, you may need to adjust the wax ring or replace it with a new one.

Remove the old wax ring from the toilet.

To remove the old wax ring from the toilet, you will need to first remove the toilet from the floor. To do this, you will need to disconnect the water supply line to the toilet and the drain line. Once the toilet is disconnected, you can lift it up and off of the floor.

Once the toilet is off of the floor, you can remove the old wax ring. The old wax ring will be located at the bottom of the toilet bowl, and it will be held in place by a metal ring. You can use a putty knife or a utility knife to carefully pry the old wax ring out of place.

Once the old wax ring has been removed, you can clean the bottom of the toilet bowl with a degreaser or a toilet bowl cleaner. This will help to remove any residue from the old wax ring.

Installing a wax ring on a Kohler toilet is a relatively simple process. However, it is important to follow the steps carefully to ensure that the wax ring is installed correctly. By following the steps in this guide, you can easily install a new wax ring on your Kohler toilet.

What size wax ring do I need for my Kohler toilet?

The size of the wax ring you need for your Kohler toilet will depend on the diameter of the toilet drain. The most common size is 3 1/2 inches, but you may need a larger or smaller size depending on your specific toilet. To measure the diameter of your toilet drain, use a ruler to measure the distance between the inside edges of the two bolts that hold the toilet to the floor.

How do I install a wax ring on my Kohler toilet?

To install a wax ring on your Kohler toilet, follow these steps:

1. Remove the old wax ring from the toilet.
2. Apply a thin layer of plumber’s grease to the bottom of the toilet bowl.
3. Center the new wax ring on the drain flange.
4. Lower the toilet onto the wax ring.
5. Tighten the bolts that hold the toilet to the floor.

What are the symptoms of a bad wax ring?

There are a few signs that indicate you may have a bad wax ring:

  • A slow leak from the bottom of the toilet.
  • Water pooling around the base of the toilet.
  • A musty smell coming from the toilet.
  • The toilet rocking back and forth when you sit on it.

If you notice any of these signs, it’s important to have the wax ring replaced as soon as possible. A bad wax ring can allow water to leak into the floor, which can damage your flooring and subfloor. It can also create a health hazard by allowing bacteria to grow.

**How often should I replace the wax ring on my Kohler toilet?

The wax ring on your Kohler toilet should be replaced every 5 to 10 years. However, you may need to replace it more often if you notice any of the signs of a bad wax ring listed above.

**Where can I buy a wax ring for my Kohler toilet?

You can purchase a wax ring for your Kohler toilet at most hardware stores. You can also find them online at a variety of retailers.

the size of the wax ring for a Kohler toilet depends on the diameter of the toilet bowl. The most common size is 10 inches, but there are also 12-inch and 14-inch rings available. To determine the correct size for your toilet, measure the inside diameter of the bowl. Once you have the correct size, you can install the wax ring by following the instructions included with the product. By following these steps, you can ensure that your toilet is properly sealed and that you will not experience any leaks.

Here are some key takeaways to remember when choosing a wax ring for your Kohler toilet:

  • The size of the wax ring should match the diameter of the toilet bowl.
  • The wax ring should be thick enough to create a tight seal.
  • The wax ring should be installed correctly to prevent leaks.

By following these tips, you can ensure that your toilet is properly sealed and that you will not experience any leaks.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.