How to Tile Around a Toilet Without Removing the Toilet | The Tile Guru

AvatarByLiana Farrell Toilet Queries

How to Tile Around a Toilet Without Removing the Toilet

Tiling around a toilet is a common DIY project, but it can be tricky if you don’t know what you’re doing. One of the biggest challenges is figuring out how to tile around the toilet without removing it. After all, removing the toilet can be a messy and time-consuming process.

In this article, we’ll show you how to tile around a toilet without removing it. We’ll provide step-by-step instructions, as well as tips and tricks to help you get the job done right.

So if you’re ready to give this project a try, read on!

Step Instructions Image
1 Measure the area around the toilet that you want to tile.
2 Cut the tiles to size, using a tile saw or a wet saw.
3 Apply a thin layer of thinset mortar to the back of the tiles.
4 Press the tiles firmly into place, making sure that they are level.
5 Allow the thinset mortar to dry completely, according to the manufacturer’s instructions.
6 Apply a grout sealer to the tiles to protect them from water damage.

Tiling around a toilet can be a daunting task, but it is definitely doable if you have the right tools and materials. In this guide, we will walk you through the process of tiling around a toilet without removing the toilet. We will provide step-by-step instructions and tips to help you get the job done correctly.

Tools and Materials

The following tools and materials are required to tile around a toilet without removing the toilet:

  • Tape measure
  • Level
  • Pencil
  • Utility knife
  • Grout float
  • Grout sponge
  • Grout bag
  • Tile saw
  • Safety glasses
  • Gloves
  • Waterproof sealant

Preparation

Before you begin tiling around the toilet, there are a few things you need to do to prepare the area.

1. Remove the toilet seat. This will give you access to the area behind the toilet and make it easier to install the tiles.
2. Clean the area around the toilet with a degreaser. This will remove any dirt, grease, or other debris that could interfere with the installation of the tiles.
3. Apply painter’s tape to the floor and walls around the toilet to protect them from grout and sealant. This will help to keep the area clean and make it easier to clean up any mess.
4. Mark the height of the tiles on the wall with a pencil. This will help you to ensure that the tiles are installed evenly.

Installation

Now that the area is prepared, you can begin installing the tiles.

1. Start by cutting the tiles to size. You can use a tile saw to do this.
2. Apply a thin layer of mortar to the back of the tiles. Use a trowel to spread the mortar evenly.
3. Press the tiles firmly into the mortar. Make sure that the tiles are level and that they are aligned with the other tiles.
4. Use a grout float to smooth out the mortar between the tiles. Be careful not to apply too much pressure, as this could damage the tiles.
5. Allow the mortar to dry completely. This may take several days.
6. Seal the tiles with a waterproof sealant. This will help to protect the tiles from moisture and damage.

Tiling around a toilet can be a challenging task, but it is definitely doable if you follow these steps. By taking your time and being careful, you can create a beautiful and durable tiled floor around your toilet.

Here are some additional tips for tiling around a toilet:

  • Use a level to make sure that the tiles are installed evenly.
  • Use a sharp utility knife to cut the tiles to size.
  • Apply a thin layer of mortar to the back of the tiles.
  • Press the tiles firmly into the mortar.
  • Use a grout float to smooth out the mortar between the tiles.
  • Allow the mortar to dry completely.
  • Seal the tiles with a waterproof sealant.

By following these tips, you can tile around your toilet without removing the toilet and create a beautiful and durable tiled floor.

3. Installing the Tiles

To install the tiles, you will need:

  • A tile saw
  • Thinset mortar
  • A trowel
  • A level
  • A rubber mallet
  • Tile spacers
  • A grout float
  • A grout sponge
  • A wet saw
  • Safety glasses
  • A dust mask

1. Cut the tiles to size with a tile saw.
2. Apply thinset mortar to the back of the tiles and press them into place on the wall.
3. Use a level to make sure the tiles are level.
4. Tap the tiles into place with a rubber mallet.
5. Insert tile spacers between the tiles to create grout joints.
6. Allow the thinset mortar to dry completely.

4. Grouting the Tiles

To grout the tiles, you will need:

  • Grout
  • A grout float
  • A grout sponge
  • A wet saw
  • Safety glasses
  • A dust mask

1. Mix the grout according to the package directions.
2. Apply the grout to the joints between the tiles with a grout float.
3. Use a grout sponge to wipe away excess grout.
4. Allow the grout to dry completely.

5. Sealing the Tiles

To seal the tiles, you will need:

  • A tile sealer
  • A brush

1. Apply the tile sealer to the tiles with a brush.
2. Allow the sealer to dry completely.

6. Replacing the Toilet

To replace the toilet, you will need:

  • A new toilet
  • A toilet flange
  • A wax ring
  • A toilet gasket
  • A toilet seat
  • A wrench
  • A plunger
  • A bucket
  • A wet saw
  • Safety glasses
  • A dust mask

1. Remove the old toilet.
2. Install the new toilet flange.
3. Apply a wax ring to the bottom of the new toilet.
4. Place the new toilet on the flange.
5. Tighten the bolts that secure the toilet to the floor.
6. Install the toilet gasket and seat.
7. Flush the toilet to test it.

7. Cleaning the Tiles

To clean the tiles, you will need:

  • A bucket
  • A sponge
  • A mild detergent
  • Water

1. Fill the bucket with warm water and mild detergent.
2. Dip the sponge into the solution and wring it out.
3. Wipe the tiles with the sponge.
4. Rinse the tiles with clean water.
5. Dry the tiles with a towel.

Tiling around a toilet without removing the toilet is a relatively simple process, but it does require some careful planning and execution. By following these steps, you can tile your bathroom without having to remove the toilet.

How to Tile Around a Toilet Without Removing the Toilet?

Q: Is it possible to tile around a toilet without removing the toilet?

A: Yes, it is possible to tile around a toilet without removing the toilet. However, it is a more difficult and time-consuming process than tiling around a toilet that has been removed.

Q: What are the steps involved in tiling around a toilet without removing the toilet?

A: The steps involved in tiling around a toilet without removing the toilet are as follows:

1. Prepare the area. Remove the toilet seat and clean the area around the toilet thoroughly. Apply a coat of primer to the walls and floor around the toilet.
2. Install the tile backer board. Cut the tile backer board to size and install it around the toilet using construction adhesive and screws.
3. Apply the mortar. Apply a thin layer of mortar to the backer board and press the tiles into place. Use a grout float to smooth the mortar and remove any excess.
4. Grouting the tiles. Allow the mortar to dry completely, then apply a grout to the joints between the tiles. Use a grout float to press the grout into the joints and remove any excess.
5. Sealing the tiles. Once the grout has dried completely, apply a sealant to the tiles to protect them from water damage.

Q: What are the benefits of tiling around a toilet without removing the toilet?

A: There are a few benefits to tiling around a toilet without removing the toilet. These benefits include:

  • Less time and effort. Tiling around a toilet without removing the toilet is a less time-consuming and labor-intensive process than tiling around a toilet that has been removed.
  • Less mess. Tiling around a toilet without removing the toilet creates less mess than tiling around a toilet that has been removed.
  • Less damage to the toilet. Tiling around a toilet without removing the toilet is less likely to damage the toilet than tiling around a toilet that has been removed.

Q: What are the drawbacks of tiling around a toilet without removing the toilet?

A: There are a few drawbacks to tiling around a toilet without removing the toilet. These drawbacks include:

  • More difficult. Tiling around a toilet without removing the toilet is a more difficult and time-consuming process than tiling around a toilet that has been removed.
  • More risk of mistakes. Tiling around a toilet without removing the toilet is more likely to result in mistakes than tiling around a toilet that has been removed.
  • More difficult to fix mistakes. Mistakes that are made while tiling around a toilet without removing the toilet are more difficult to fix than mistakes that are made while tiling around a toilet that has been removed.

Q: Is it possible to tile around a toilet that is not level?

A: It is possible to tile around a toilet that is not level, but it is more difficult and time-consuming than tiling around a toilet that is level.

Q: What are the steps involved in tiling around a toilet that is not level?

A: The steps involved in tiling around a toilet that is not level are as follows:

1. Prepare the area. Remove the toilet seat and clean the area around the toilet thoroughly. Apply a coat of primer to the walls and floor around the toilet.
2. Install the tile backer board. Cut the tile backer board to size and install it around the toilet using construction adhesive and screws.
3. Apply the mortar. Apply a thin layer of mortar to the backer board and press the tiles into place. Use a grout float to smooth the mortar and remove any excess.
4. Grouting the tiles. Allow the mortar to dry completely, then apply a grout to the joints between the tiles. Use a grout float to press the grout into the joints and remove any excess.
5. Sealing the tiles. Once the grout has dried completely, apply a sealant to the tiles to protect them from water damage.

Q: What are the best materials to use when tiling around a toilet?

A: The best materials to use when tiling around a toilet include:

* **

tiling around a toilet without removing the toilet is a relatively simple process, but it does require some careful planning and execution. By following the steps outlined in this article, you can achieve a professional-looking finished product that will add value to your home.

Here are the key takeaways from this article:

  • Before you begin, make sure you have all of the necessary tools and materials.
  • Carefully measure and mark the area where you will be tiling.
  • Use a stud finder to locate the studs behind the wall.
  • Apply a thin coat of adhesive to the back of the tiles.
  • Press the tiles firmly into place, using a rubber mallet if necessary.
  • Use a grout float to apply grout between the tiles.
  • Allow the grout to dry completely before using the toilet.

By following these steps, you can tile around a toilet without removing the toilet and create a beautiful and durable addition to your bathroom.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.