How to Take Apart a Delta Shower Faucet
To take apart a Delta shower faucet, shut off the water, remove the handle and trim, take off the bonnet or retaining clip, and pull out the cartridge or stem assembly. The exact parts vary by Delta valve series, so identify the valve before ordering a replacement or forcing anything loose. Most of the job is simple work, but stop if the valve body moves in the wall or water cannot be shut off.
How Delta Shower Faucets Come Apart
A Delta shower faucet has two groups of parts:
- Trim parts: the handle, decorative sleeve, escutcheon plate, and screws visible from the shower.
- Valve parts: the bonnet nut or retaining clip, cartridge or stem, seals, and the brass valve body inside the wall.
The cartridge or stem controls water flow and temperature. A worn cartridge commonly causes a drip from the tub spout or showerhead even when the handle is off.
Some Delta faucets have one handle, while others have separate hot and cold handles or a separate temperature-control handle. The removal order is similar, but the internal part is not always the same.
How to Take Apart a Delta Shower Faucet
The trim style is not a reliable way to choose a Delta cartridge; the matched parts diagram is.
Before buying a part, use Delta’s Product Identifier Tool to narrow down the model. The matched product page includes a parts list and parts diagram, which lets you confirm the cartridge, bonnet, clip, screws, and any seals before you remove the faucet.
| Confirmed Delta valve family | Replacement part and identification detail |
|---|---|
| 1300 / 1400 Series with “04/2006 And Earlier” on the matched parts listing | Cartridge assembly RP19804. Delta’s current RP19804 began shipping in 2015 and replaces Monitor series valves that use RP19804. |
| 1600 Series valve manufactured from 1974–1993 | RP1991 stem unit and seats. The kit includes the seats, so this is a stem-and-seat repair rather than a cartridge-only repair. |
| MultiChoice Universal 13 / 14 Series | RP46074 cartridge assembly. The current MultiChoice T13/14 cartridge began shipping in 2015. |
| MultiChoice Universal 17 Series, 2007–present | RP46463 cartridge assembly. A lighter gray cap was used until 2016; cap color is only a supporting clue, not proof of the correct part. |
| MultiChoice Universal 17T TempAssure Series | RP47201 cartridge assembly. |
Step 1: Gather Tools and Confirm the Repair Part
You will usually need:
- Allen wrenches or hex keys
- Small flat-head screwdriver
- Phillips screwdriver
- Needle-nose pliers
- Adjustable pliers or tongue-and-groove pliers
- A towel or drain cover
- Faucet grease for cartridge O-rings
- The correct replacement cartridge, stem, seats, or seals
Take a clear photo of the handle and trim before removing anything. Handles and trim can be changed without changing the valve behind the wall.
If your faucet is a 1600 Series valve from 1974–1993, have the RP1991 stem-and-seat kit ready before disassembly. Do not buy a standard cartridge for that repair.
Step 2: Shut Off the Water and Protect the Shower
- Turn off the shower’s local shutoffs if your bathroom has them. They may be behind an access panel on the opposite side of the shower wall.
- If there are no local shutoffs, turn off the home’s main water supply.
- Open the shower faucet to release pressure and drain the water left in the valve.
- Cover the shower drain with a towel so screws, clips, and small parts cannot fall into it.
A cartridge can come out suddenly and release water into the wall or shower.
Step 3: Remove the Handle
Look closely at the handle before pulling on it. Delta handles are commonly held by a recessed set screw, a center screw hidden behind a cap, or a screw below a lever.
- Look for a small recessed hole on the side, underside, or back of the handle.
- Insert the correct Allen wrench and loosen the set screw. You usually do not need to remove it completely.
- Pull the handle straight away from the wall.
- If the faucet has a separate lever section, remove that piece first when it blocks access to the set screw.
- If there is a decorative center cap, carefully pry it off with a small screwdriver and remove the screw beneath it.
Set the handle and screw aside together. If your faucet has more than one handle, keep the hot- and cold-side parts separate.
Step 4: Remove the Sleeve and Escutcheon Plate
After the handle is off, you may see a chrome sleeve, plastic limit-stop pieces, or a trim collar around the valve stem.
- Slide or unscrew the decorative sleeve from the valve.
- Take a photo of any plastic temperature-limit stop or adapter before removing it.
- Remove the screws holding the escutcheon plate to the wall if you need more room or need to inspect for a leak behind the plate.
- Pull the plate forward carefully without damaging the wall finish.
You do not always need to remove the escutcheon plate to replace a cartridge, but removing it gives you room to work and lets you check for moisture behind the trim.
Step 5: Remove the Bonnet Nut or Retaining Clip
The part holding the cartridge in place depends on the valve design.
- Identify whether your valve uses a threaded bonnet nut, a retaining ring, or a U-shaped retaining clip.
- For a bonnet nut, turn it counterclockwise by hand to remove it.
- For a retaining clip, use needle-nose pliers to pull the clip straight out. Keep it where it cannot fall down the drain.
- If there is an adapter or temperature-control assembly in front of the cartridge, photograph it and remove its components in order.
An older bonnet may need gentle help from tongue-and-groove pliers to break it loose. Protect the finish with a cloth while using gentle pressure to loosen the bonnet.
Step 6: Pull Out the Cartridge or Stem Assembly
Grip the exposed cartridge stem and pull it straight toward you. Wiggle it slightly up and down if it is tight, but do not twist or pry against the brass valve body.
Before removing it completely:
- Take a photo of its orientation.
- Look for an “H,” hot-side marking, or alignment tabs.
- Note the position of any adapter, seal, or rotational limit stop.
Once the old part is out, compare it with the replacement. The tabs, stem shape, seals, and depth should match. A MultiChoice 13/14 valve uses RP46074, while a MultiChoice 17 valve uses RP46463; the two should not be substituted based on appearance alone.
If you are installing a new cartridge, apply a small dab of faucet grease to its O-rings. Slide it straight into the valve body in the same orientation as the old one. If it will not seat fully, remove it and check the alignment.
Step 7: Reinstall the Retainer and Trim
- Reinstall the retaining clip, retaining ring, or bonnet nut.
- Tighten a bonnet nut by hand only.
- Refit any adapter, temperature-limit stop, sleeve, and escutcheon plate in the order shown in your photo.
- Reinstall the handle.
- Tighten the handle’s set screw enough to hold the handle securely, but do not overtighten it.
A handle that is difficult to turn after reassembly may indicate that the cartridge, adapter, or limit stop is not seated correctly. Turn the water back off and correct the alignment before testing the handle again.
Step 8: Restore Water and Test the Faucet
Open the shutoff or shutoffs you closed slowly about halfway first, then watch the shower valve and trim area for leaks. Once there is no immediate leak, open the shutoff or shutoffs fully.
Test the faucet in this order:
- Turn the handle to off and check whether water stops completely.
- Run cold water, then hot water.
- Move the handle through its full range to make sure it does not bind.
- Switch between tub and shower, if applicable.
- Check around the handle and escutcheon plate for drips.
If the faucet continues to drip from the spout after a correctly installed cartridge, verify that the cartridge matches the valve series and is fully seated.
Freeing Stuck Delta Shower Faucet Parts
Stuck shower faucet parts can be freed by fully loosening fasteners, pulling straight out steadily, and using a puller when needed.
A Handle That Will Not Pull Off
First, make sure the set screw or center screw is fully loose. A handle can feel stuck even when the screw is still catching the stem.
Pull from the handle hub near the wall rather than from the end of a lever. Rock it gently side to side while pulling straight out.
If the handle remains seized, a faucet handle puller is safer than bending or crushing the handle with pliers. Once it releases, remove the trim, cartridge retainer, and cartridge; then reinstall the valve parts, trim, and handle before restoring the water and testing for leaks.
A Bonnet Nut or Cartridge That Is Stuck
Mineral buildup can seize an older bonnet nut or cartridge.
For a stuck bonnet, protect it with a cloth and use adjustable pliers only to loosen it counterclockwise. Do not crush the nut or tighten it with pliers during reassembly.
For a stuck cartridge, remove the retaining clip or bonnet completely, then pull straight out with steady pressure. A cartridge puller may be needed for a cartridge that is fused in place. Do not hammer the valve body or pry inside it with a screwdriver; damage inside the wall can turn a simple cartridge replacement into a valve replacement.
After the cartridge comes out, install the correct replacement, hand-tighten the bonnet or reinstall the clip, put the trim back together, restore water slowly, and check the faucet through its full hot-and-cold range.
A Stuck Tub-and-Shower Diverter
A shower-tub diverter control can become stuck. If the main faucet handle works but water will not transfer from the tub spout to the showerhead, the diverter may be a separate repair from the mixing cartridge.
Identify the affected component first, because the repair may involve the tub spout, a diverter stem, or a separate valve component.
Confirm the Repair Before Closing Up
Before calling the job finished, confirm all of these points:
- The handle turns smoothly from off through cold and hot.
- Water shuts off fully.
- No water drips from the handle, escutcheon plate, tub spout, or showerhead.
- The trim plate sits flat against the wall.
- The tub-to-shower diverter works, if your fixture has one.
- No moisture appears behind or below the trim after the faucet has run.
Keep the old cartridge or stem until the faucet has worked properly for a few days. It can help confirm the part number if you need to exchange a replacement.
When to Call a Plumber
Call a plumber instead of continuing if:
- You cannot shut off the water supply.
- The brass valve body moves inside the wall.
- A pipe leaks behind the shower wall.
- The retaining clip, bonnet threads, or valve body is damaged.
- The cartridge breaks apart and pieces remain inside the valve.
- The repair requires opening tile, drywall, or the shower surround.
- You find corrosion severe enough that the valve body may fail.
Replacing the valve body behind the wall is a larger plumbing repair and may require access from another room.
Frequently Asked Questions
How Do I Remove an Older Delta Single-Handle Shower Faucet?
Shut off the water, loosen the handle’s recessed set screw, remove the handle and sleeve, then remove the bonnet or retaining clip before pulling the internal part straight out. For a 1300 / 1400 Series valve with “04/2006 And Earlier” on its matched parts listing, the replacement cartridge is RP19804. Delta’s current RP19804 began shipping in 2015 and replaces Monitor valves that use RP19804.
How Do I Replace a Delta RP46074 Cartridge?
RP46074 is the cartridge for a MultiChoice Universal 13 / 14 Series valve. Shut off the water, remove the handle and trim, take off the bonnet or retaining clip, and pull the old cartridge straight out. Apply a small dab of faucet grease to the replacement cartridge’s O-rings, align it exactly with the valve body, reinstall the retainer and trim, then restore water slowly and test for leaks.
Can I Remove a Delta Shower Handle Without Turning Off the Water?
You can often remove only the handle without shutting off the water, but turn the water off before removing trim that exposes the cartridge, bonnet, retaining clip, or valve opening. A loosened or damaged cartridge can release water unexpectedly. Shutting off the water before starting also lets you test the faucet safely once it is reassembled.
How Do I Replace a Bathtub Faucet or Spout?
First determine whether you mean the tub spout or the shower valve handle. A tub spout may be held by a small set screw underneath or may thread onto a pipe; after shutting off water, loosen the set screw and pull the spout off, or turn a threaded spout counterclockwise. If the pipe turns with the spout or the connection is hidden in the wall, stop and call a plumber rather than risk breaking the pipe. Otherwise, install the replacement spout, restore the water, and check for leaks.
How can you identify the right Delta shower cartridge?
Use the Product Identifier Tool to narrow your faucet to a model, then consult that model’s parts list and diagram. Delta shower faucets do not all use one cartridge: MultiChoice Universal 13 / 14 uses RP46074, while MultiChoice Universal 17 uses RP46463.
How do you remove a Delta shower handle when no screws are visible?
Check the handle for a set screw hidden in a recessed spot; with certain styles, remove the lever first to expose it. Loosen that screw before pulling the handle away from the wall.
