How To Replace Toilet Seat With Hidden Bolts?

AvatarByLiana Farrell Toilet Queries

How to Replace a Toilet Seat with Hidden Bolts

Your toilet seat is one of the most used items in your home, so it’s important to keep it in good condition. If your toilet seat is cracked, broken, or simply worn out, it’s time to replace it. Replacing a toilet seat is a relatively simple task that can be completed in just a few minutes. However, if your toilet seat has hidden bolts, the process may be a bit different.

In this article, we will walk you through the steps on how to replace a toilet seat with hidden bolts. We’ll provide detailed instructions and images to help you along the way. So, if you’re ready to give your toilet a new look, read on!

Step Instructions Images
1 Locate the hidden bolts under the toilet seat.
2 Insert a screwdriver into the hole and turn counterclockwise to loosen the bolt.
3 Repeat step 2 for all of the bolts.
4 Lift up on the toilet seat and remove it.
5 Clean the toilet bowl and the toilet seat.
6 Align the new toilet seat with the bowl and insert the bolts through the holes.
7 Turn the bolts clockwise to tighten them.
8 Lower the toilet seat and check to make sure it is secure.

A toilet seat is a critical part of your bathroom, and it’s important to make sure that it’s in good condition. If your toilet seat is cracked, broken, or loose, it’s time to replace it. Replacing a toilet seat with hidden bolts is a relatively simple task that can be completed in about 30 minutes.

This guide will walk you through the process of replacing a toilet seat with hidden bolts. We’ll provide step-by-step instructions and images to help you along the way.

Gather the necessary tools and materials

To replace a toilet seat with hidden bolts, you will need the following tools and materials:

  • Adjustable wrench
  • Pliers
  • Replacement toilet seat
  • New bolts (if necessary)
  • Silicone sealant
  • Paper towels
  • Rag

Remove the old toilet seat

1. Lift up the toilet seat and locate the bolts that are holding it in place.
2. Use the adjustable wrench to loosen the bolts.
3. Carefully lift the toilet seat off of the bowl.

Install the new toilet seat

1. Place the new toilet seat on the bowl.
2. Align the holes in the toilet seat with the bolts in the bowl.
3. Insert the bolts through the holes in the toilet seat and into the bowl.
4. Tighten the bolts with the adjustable wrench.

**

Apply silicone sealant

1. Apply a small amount of silicone sealant around the edge of the toilet seat.
2. Press the toilet seat down firmly to create a seal.
3. Allow the silicone sealant to dry completely.

**

Replacing a toilet seat with hidden bolts is a relatively simple task that can be completed in about 30 minutes. By following these steps, you can easily replace your old toilet seat with a new one.

Here are some additional tips for replacing a toilet seat with hidden bolts:

  • If the bolts are rusted or corroded, you may need to use a penetrating oil to loosen them.
  • Be careful not to overtighten the bolts, as this could damage the toilet seat.
  • If you have any questions or concerns, consult with a qualified plumber.

How To Replace Toilet Seat With Hidden Bolts?

Replacing a toilet seat with hidden bolts is a relatively simple task that can be completed in a few minutes. However, it is important to follow the steps carefully in order to ensure that the new seat is installed correctly and securely.

1. Gather your materials.

To replace a toilet seat with hidden bolts, you will need the following materials:

  • A new toilet seat
  • A Phillips head screwdriver
  • An adjustable wrench
  • A sealant (such as silicone sealant)
  • Paper towels

2. Remove the old toilet seat.

The first step is to remove the old toilet seat. To do this, you will need to:

1. Locate the two bolts that are located on the underside of the toilet seat.
2. Insert the Phillips head screwdriver into the head of each bolt and turn counterclockwise to loosen.
3. Once the bolts are loose, you can lift the toilet seat off of the bowl.

3. Install the new toilet seat.

Now that the old toilet seat is removed, you can install the new one. To do this, you will need to:

1. Place the new toilet seat on the bowl.
2. Align the holes in the seat with the bolts in the bowl.
3. Insert the bolts through the holes in the seat and tighten them with the adjustable wrench.

4. Apply sealant around the base of the toilet seat.

The final step is to apply a sealant around the base of the toilet seat. This will help to prevent water from leaking underneath the seat. To do this, you will need to:

1. Apply a thin layer of silicone sealant around the base of the toilet seat.
2. Use the paper towels to wipe away any excess sealant.
3. Allow the sealant to dry completely before using the toilet.

.

Replacing a toilet seat with hidden bolts is a relatively simple task that can be completed in a few minutes. By following the steps outlined in this guide, you can ensure that the new seat is installed correctly and securely.

How do I remove the old toilet seat?

1. Locate the hidden bolts. The hidden bolts are typically located on the back of the toilet bowl, just below the rim. They are often covered by a plastic caps.
2. Remove the plastic caps. You can use a flathead screwdriver to pry the caps off.
3. Loosen the bolts. Use a wrench to loosen the bolts. Turn the wrench counterclockwise.
4. Lift the toilet seat off. Once the bolts are loose, you can lift the toilet seat off of the bowl.

How do I install the new toilet seat?

1. Place the new toilet seat on the bowl. Make sure that the holes in the seat align with the bolts in the bowl.
2. Insert the bolts through the holes in the seat.
3. Secure the bolts with the nuts. Use a wrench to tighten the nuts clockwise.
4. Replace the plastic caps. Put the plastic caps back on the bolts to cover them.

What if the bolts are stuck?

If the bolts are stuck, you can try using a penetrating oil to loosen them. Spray the oil on the bolts and let it sit for a few minutes. Then, try to loosen the bolts again with the wrench.

What if the new toilet seat doesn’t fit?

If the new toilet seat doesn’t fit, you may need to adjust the position of the bolts. To do this, loosen the nuts and move the bolts to a different position. Then, tighten the nuts again.

What if I have other questions?

If you have other questions about replacing a toilet seat with hidden bolts, you can contact a plumber or a home improvement store.

Replacing a toilet seat with hidden bolts is a relatively simple task that can be completed in a few minutes. However, it is important to follow the steps carefully to ensure that the new seat is installed correctly and securely.

This guide has outlined the steps involved in replacing a toilet seat with hidden bolts. By following these steps, you can easily and safely replace your old toilet seat with a new one.

Here are some key takeaways to remember:

  • Always turn off the water supply to the toilet before beginning the replacement process.
  • Use a wrench to loosen the nuts on the bolts that are holding the old seat in place.
  • Remove the old seat and clean the toilet bowl.
  • Apply a thin layer of plumber’s grease to the threads of the new bolts.
  • Insert the new bolts through the holes in the toilet bowl and tighten them with a wrench.
  • Replace the toilet seat and turn on the water supply.

By following these steps, you can easily and safely replace your old toilet seat with a new one.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.