How to Replace a Toilet Flange in Concrete: A Step-by-Step Guide

AvatarByLiana Farrell Toilet Queries

How to Replace a Toilet Flange in Concrete

A toilet flange is a critical part of your toilet. It’s the metal ring that connects the toilet to the drainpipe, and it helps to create a watertight seal. Over time, the toilet flange can become damaged or worn out, and it will need to be replaced. Replacing a toilet flange in concrete is a relatively simple DIY project, but it’s important to do it correctly to avoid leaks.

In this article, we’ll walk you through the steps of replacing a toilet flange in concrete. We’ll provide you with detailed instructions, tips, and warnings. By the end of this article, you’ll be able to replace your toilet flange like a pro.

What You’ll Need

Before you get started, gather all of the materials and tools you’ll need. Here’s a list of what you’ll need:

  • New toilet flange
  • Silicone sealant
  • Penetrating oil
  • Adjustable wrench
  • Pliers
  • Hammer
  • Tape measure
  • Level
  • Utility knife
  • Bucket
  • Shop vac

Step-by-Step Instructions

Step Instructions Images
1 Turn off the water supply to the toilet.
2 Remove the toilet seat.
3 Locate the toilet flange.
4 Remove the old flange.
5 Apply a bead of silicone sealant around the new flange.
6 Place the new flange over the drain pipe.
7 Secure the flange with bolts.
8 Reattach the toilet seat.
9 Turn on the water supply to the toilet.

A toilet flange is a metal or plastic ring that connects the toilet to the drainpipe. It is an important part of the toilet, as it helps to create a seal between the toilet and the drainpipe, preventing leaks. Over time, the toilet flange can become damaged or worn out, and will need to be replaced. Replacing a toilet flange is a relatively simple DIY project, but it is important to follow the steps carefully to ensure that the job is done correctly.

Tools and Materials

The following tools and materials will be needed to replace a toilet flange in concrete:

  • Toilet flange
  • Hacksaw
  • Claw hammer
  • Replacement wax ring
  • Silicone sealant
  • Penetrating oil
  • Pliers
  • Level
  • Tape measure

Step-by-step Instructions

1. Turn off the water supply to the toilet. This can be done by turning the shut-off valve located under the sink or behind the toilet.
2. Remove the toilet seat. There will be two bolts located on the underside of the toilet seat. Use a screwdriver to loosen these bolts and remove the seat.
3. Disconnect the water supply line. The water supply line is located on the back of the toilet. Use a pair of pliers to loosen the nut that connects the water supply line to the toilet.
4. Remove the old toilet flange. The toilet flange is located at the bottom of the toilet. It is a metal or plastic ring that connects the toilet to the drainpipe. Use a hacksaw to cut through the bolts that hold the flange in place. Then, use a claw hammer to pry the flange off of the drainpipe.
5. Clean the drainpipe. Use a putty knife or other sharp object to remove any old wax or sealant from the drainpipe.
6. Apply a new wax ring to the toilet. The wax ring is a rubber ring that creates a seal between the toilet and the drainpipe. It is important to make sure that the wax ring is properly seated on the drainpipe.
7. Install the new toilet flange. Place the new toilet flange over the drainpipe. Then, use a hacksaw to cut through the bolts that hold the flange in place. Finally, use a claw hammer to secure the flange to the drainpipe.
8. Reattach the water supply line. Connect the water supply line to the toilet. Make sure that the nut is tight enough to prevent leaks.
9. Reinstall the toilet seat. Place the toilet seat back on the toilet and tighten the bolts.
10. Turn on the water supply to the toilet. Flush the toilet to make sure that there are no leaks.

Replacing a toilet flange in concrete is a relatively simple DIY project, but it is important to follow the steps carefully to ensure that the job is done correctly. By following these steps, you can replace your toilet flange in no time and have a leak-free toilet for years to come.

How to Replace a Toilet Flange in Concrete

Replacing a toilet flange is a relatively simple plumbing task that can be completed in about an hour. However, it is important to follow the steps carefully to ensure that the new flange is installed correctly and that the toilet will be properly supported.

Tools and Materials

To replace a toilet flange, you will need the following tools and materials:

  • A hacksaw or reciprocating saw
  • A screwdriver
  • A hammer
  • A putty knife
  • A new toilet flange
  • A wax ring
  • Plumbing putty
  • Silicone sealant
  • A bucket of water

Step 1: Shut off the water supply to the toilet

The first step is to shut off the water supply to the toilet. This can be done by turning off the shut-off valve located under the sink or behind the toilet. Once the water supply is turned off, you will need to flush the toilet to drain any remaining water.

Step 2: Remove the toilet from the flange

The next step is to remove the toilet from the flange. To do this, you will need to loosen the nuts that hold the toilet to the floor. These nuts are typically located on the back of the toilet, near the floor. Once the nuts are loosened, you can use a pry bar or a hammer to gently pry the toilet away from the flange.

Step 3: Remove the old flange

Once the toilet is removed, you can remove the old flange. The flange is a metal ring that is attached to the floor and supports the toilet. To remove the flange, you will need to use a hacksaw or reciprocating saw to cut through the flange. Be careful not to damage the subfloor.

Step 4: Install the new flange

The next step is to install the new flange. The new flange should be the same size as the old flange. To install the flange, you will need to apply a bead of plumber’s putty around the edge of the flange. Then, you can place the flange on the floor and press it down firmly.

Step 5: Apply the wax ring

The next step is to apply the wax ring to the toilet. The wax ring is a rubber ring that creates a seal between the toilet and the flange. To apply the wax ring, you will need to spread a thin layer of plumber’s putty around the edge of the toilet bowl. Then, you can place the wax ring on top of the putty.

Step 6: Position the toilet

The next step is to position the toilet over the flange. Make sure that the toilet is centered over the flange and that the bolts are aligned with the holes in the flange.

Step 7: Secure the toilet

The final step is to secure the toilet to the flange. To do this, you will need to insert the bolts through the holes in the flange and into the holes in the toilet. Then, you can tighten the nuts on the bolts to secure the toilet in place.

Replacing a toilet flange is a relatively simple plumbing task that can be completed in about an hour. However, it is important to follow the steps carefully to ensure that the new flange is installed correctly and that the toilet will be properly supported.

If you have any questions about replacing a toilet flange, you can contact a professional plumber for assistance.

How do I remove a toilet flange from concrete?

1. Turn off the water supply to the toilet. Locate the shut-off valve under the sink or behind the toilet. Turn the valve clockwise to stop the water flow.
2. Flush the toilet to drain the water from the tank.
3. Remove the toilet seat. There are usually two bolts located on the underside of the seat. Unscrew the bolts and lift the seat off.
4. Locate the bolts that hold the toilet to the floor. There are usually two bolts on each side of the toilet. Use a wrench to loosen the bolts.
5. Insert a pry bar under the toilet flange and pry up. Be careful not to damage the floor.
6. Once the flange is loose, lift the toilet off the floor and set it aside.

How do I install a new toilet flange in concrete?

1. Clean the area around the toilet flange. Remove any dirt, debris, or old sealant.
2. Apply a bead of silicone sealant around the edge of the new flange.
3. Position the new flange over the drain hole in the floor. Make sure the flange is level.
4. Secure the flange to the floor with bolts. Use a wrench to tighten the bolts until they are snug.
5. Apply a new layer of sealant around the edge of the flange. This will help to prevent leaks.
6. Reinstall the toilet.

What are the common problems with toilet flanges?

  • Leaks. A leaking toilet flange is one of the most common plumbing problems. It can be caused by a loose or damaged flange, or by a crack in the concrete.
  • Sagging toilets. A sagging toilet is another common problem. It can be caused by a loose or damaged flange, or by a cracked toilet bowl.
  • Toilet wobble. A toilet that wobbles is usually caused by a loose or damaged flange.

How can I prevent problems with toilet flanges?

  • Install the flange correctly. Make sure the flange is level and that the bolts are tightened securely.
  • Use a high-quality sealant. A good sealant will help to prevent leaks.
  • Inspect the flange regularly. Check for leaks or damage and repair them as soon as possible.

What is the best type of toilet flange for concrete?

There are two main types of toilet flanges for concrete:

  • Plastic flanges. Plastic flanges are less expensive than metal flanges, but they are not as durable.
  • Metal flanges. Metal flanges are more expensive than plastic flanges, but they are more durable.

The best type of toilet flange for concrete is a metal flange. Metal flanges are more durable and less likely to leak than plastic flanges.

How much does it cost to replace a toilet flange?

The cost of replacing a toilet flange depends on the type of flange and the cost of labor. The average cost of a new toilet flange is between $10 and $20. The cost of labor can vary depending on the location and the complexity of the job. The total cost of replacing a toilet flange can range from $20 to $50.

Replacing a toilet flange in concrete is a relatively straightforward process, but it is important to follow the steps carefully to ensure that the new flange is properly installed and that the toilet is properly secured. By following the steps outlined in this guide, you can replace your toilet flange in concrete with confidence.

Here are the key takeaways from this guide:

  • Before you begin, make sure that you have all of the necessary tools and materials.
  • The first step is to remove the old toilet flange.
  • Once the old flange is removed, you can install the new flange.
  • Be sure to seal the new flange with plumber’s putty or silicone sealant.
  • Finally, replace the toilet and tighten the bolts.

By following these steps, you can replace your toilet flange in concrete with confidence and ensure that your toilet is properly secured.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.