How To Replace Toilet Bowl Guts?

AvatarByLiana Farrell Toilet Queries

How to Replace Toilet Bowl Guts

Your toilet is one of the most important fixtures in your home, but it’s also one of the most likely to break down. If your toilet is leaking, running, or making strange noises, it may be time to replace the toilet bowl guts. This is a relatively simple DIY project that can be completed in a few hours.

In this article, we’ll walk you through the steps of replacing toilet bowl guts, from start to finish. We’ll provide detailed instructions and images to help you along the way. By the end of this article, you’ll be able to replace your toilet bowl guts like a pro!

How To Replace Toilet Bowl Guts?

| Step | Task | Tools |
|—|—|—|
| 1 | Shut off the water supply to the toilet. | Adjustable wrench |
| 2 | Remove the toilet tank lid. | Flathead screwdriver |
| 3 | Disconnect the water supply line from the toilet tank. | Adjustable wrench |
| 4 | Remove the nuts that hold the toilet tank to the toilet bowl. | Adjustable wrench |
| 5 | Lift the toilet tank off of the toilet bowl. | |
| 6 | Remove the old toilet bowl guts. | Pliers |
| 7 | Clean the toilet bowl. | Toilet brush |
| 8 | Install the new toilet bowl guts. | Pliers |
| 9 | Reattach the toilet tank to the toilet bowl. | Adjustable wrench |
| 10 | Connect the water supply line to the toilet tank. | Adjustable wrench |
| 11 | Turn on the water supply to the toilet. | |

A toilet is a plumbing fixture that is used to flush waste and water from a bathroom. The toilet bowl is the part of the toilet that holds the water and the waste. The toilet bowl guts are the internal components of the toilet bowl that work together to flush the waste and water away.

Over time, the toilet bowl guts can wear out and need to be replaced. This can be a difficult and messy job, but it is important to do it correctly to avoid any further damage to your toilet.

In this guide, we will walk you through the process of replacing the toilet bowl guts step-by-step. We will provide you with the necessary information and tools you need to complete the job successfully.

Gather Your Materials

Before you begin, you will need to gather the following materials:

  • Toilet bowl wrench
  • Replacement toilet bowl guts
  • Pliers
  • Penetrating oil
  • Bucket
  • Gloves

Prepare the Toilet Bowl

The first step is to prepare the toilet bowl for the replacement. This involves turning off the water supply to the toilet, flushing the toilet to drain the water from the tank, and removing the toilet tank lid.

To turn off the water supply to the toilet, you will need to find the water supply valve. This is usually located behind the toilet, near the floor. Turn the valve clockwise to turn off the water supply.

Once the water supply is turned off, flush the toilet to drain the water from the tank. This will help to make the replacement process easier.

Next, remove the toilet tank lid. This is usually held in place by two screws. Unscrew the screws and remove the lid.

Finally, disconnect the water supply line from the toilet tank. The water supply line is a flexible hose that connects the toilet tank to the water supply. Disconnect the hose by unscrewing the nut that holds it in place.

Remove the Old Toilet Bowl Guts

Now that you have prepared the toilet bowl, you can begin to remove the old toilet bowl guts. This involves removing the flush valve, the flapper valve, and the toilet bowl chain.

The flush valve is located at the bottom of the toilet tank. It is a round, metal valve with a lever on top. To remove the flush valve, you will need to use a toilet bowl wrench.

The flapper valve is located at the bottom of the toilet bowl. It is a rubber disk that seals the opening of the toilet bowl when the toilet is flushed. To remove the flapper valve, you will need to use a pair of pliers.

The toilet bowl chain is a metal chain that connects the flapper valve to the flush lever. To remove the toilet bowl chain, you will need to use a pair of pliers.

Install the New Toilet Bowl Guts

Now that you have removed the old toilet bowl guts, you can install the new ones. This involves installing the flush valve, the flapper valve, and the toilet bowl chain.

The flush valve is installed in the same way that the old one was removed. The flapper valve is installed by inserting it into the opening in the bottom of the toilet bowl. The toilet bowl chain is installed by attaching it to the flapper valve and the flush lever.

Test the Toilet

Once you have installed the new toilet bowl guts, you should test the toilet to make sure that it is working properly. Flush the toilet several times and make sure that the water is flowing properly and that the toilet is sealing properly.

If the toilet is not working properly, you may need to adjust the toilet bowl chain or the flapper valve.

Replacing the toilet bowl guts is a relatively simple task, but it is important to do it correctly to avoid any further damage to your toilet. By following the steps in this guide, you can successfully replace the toilet bowl guts and have a working toilet again in no time.

Additional Tips

  • If you are having trouble removing the old toilet bowl guts, you can try using a penetrating oil to loosen them. Penetrating oil is a type of oil that helps to dissolve rust and other deposits.
  • When installing the new toilet bowl guts, make sure that they are installed correctly. If the toilet bowl guts are not installed correctly, the toilet may not work properly.
  • After you have installed the new toilet bowl guts, you should test the toilet to make sure that it is working properly.

3. Remove the Old Toilet Bowl Guts

To remove the old toilet bowl guts, you will need to:

1. Turn off the water supply to the toilet. This is usually located behind the toilet, near the floor. You will need to find the shut-off valve and turn it clockwise until it is completely closed.
2. Flush the toilet. This will empty the water from the tank and bowl.
3. Remove the nuts that hold the toilet bowl to the floor. These nuts are usually located on the back of the toilet bowl, near the floor. You will need to use a wrench to loosen them.
4. Lift the toilet bowl off of the floor. Be careful not to drop the toilet bowl, as it is heavy.
5. Remove the old toilet bowl guts from the tank. The toilet bowl guts are located inside the tank. You will need to reach into the tank and remove them.

4. Install the New Toilet Bowl Guts

To install the new toilet bowl guts, you will need to:

1. Place the new toilet bowl guts in the tank. The toilet bowl guts should fit snugly inside the tank.
2. Secure the toilet bowl guts to the tank with the nuts. You will need to use a wrench to tighten the nuts.
3. Reattach the water supply line to the toilet tank. The water supply line is usually located on the back of the toilet tank. You will need to connect the water supply line to the tank.
4. Turn on the water supply to the toilet. This is usually located behind the toilet, near the floor. You will need to find the shut-off valve and turn it counterclockwise until it is completely open.
5. Flush the toilet to check for leaks. After you have turned on the water supply to the toilet, you should flush the toilet to check for leaks. If you see any leaks, you will need to tighten the nuts on the toilet bowl guts until the leaks stop.

Replacing the toilet bowl guts is a relatively simple task that can be completed in about 30 minutes. However, it is important to follow the steps carefully to avoid damaging the toilet. If you are not comfortable doing this yourself, you can always hire a plumber to do the job for you.

How To Replace Toilet Bowl Guts?

Q: What are the tools and materials I need to replace my toilet bowl guts?

A: You will need the following tools and materials:

  • A new toilet bowl gasket
  • A new toilet flapper
  • A new toilet tank fill valve
  • A new toilet float
  • A new toilet supply line
  • A screwdriver
  • A wrench
  • A pair of pliers
  • A bucket
  • A wet/dry vacuum

Q: How do I remove the old toilet bowl guts?

A: To remove the old toilet bowl guts, follow these steps:

1. Turn off the water supply to the toilet.
2. Flush the toilet to drain the water from the tank.
3. Remove the cap from the toilet tank.
4. Loosen the nuts that connect the toilet tank to the toilet bowl.
5. Lift the toilet tank off of the toilet bowl.
6. Remove the old toilet bowl gasket, flapper, tank fill valve, float, and supply line.

Q: How do I install the new toilet bowl guts?

A: To install the new toilet bowl guts, follow these steps:

1. Apply a thin layer of plumber’s putty to the toilet bowl flange.
2. Place the new toilet bowl gasket on the toilet bowl flange.
3. Insert the new toilet flapper into the toilet tank.
4. Connect the new toilet tank fill valve to the water supply line.
5. Connect the new toilet float to the tank fill valve.
6. Connect the new toilet supply line to the toilet tank.
7. Replace the cap on the toilet tank.
8. Turn on the water supply to the toilet.
9. Flush the toilet to test the new toilet bowl guts.

Q: What are some common problems with toilet bowl guts?

A: Some common problems with toilet bowl guts include:

  • A leaky toilet tank
  • A toilet that won’t flush
  • A toilet that runs constantly
  • A toilet that makes a gurgling noise

Q: How can I fix a leaky toilet tank?

A: To fix a leaky toilet tank, follow these steps:

1. Turn off the water supply to the toilet.
2. Flush the toilet to drain the water from the tank.
3. Remove the cap from the toilet tank.
4. Look for any leaks around the toilet tank gasket.
5. If you find a leak, apply a thin layer of plumber’s putty to the gasket and re-install the cap.
6. Turn on the water supply to the toilet.
7. Flush the toilet to test the repair.

Q: How can I fix a toilet that won’t flush?

A: To fix a toilet that won’t flush, follow these steps:

1. Turn off the water supply to the toilet.
2. Flush the toilet to drain the water from the tank.
3. Remove the cap from the toilet tank.
4. Check the toilet flapper to make sure it is not stuck.
5. If the flapper is stuck, try to unstick it by gently prying it up with a screwdriver.
6. If the flapper is not stuck, check the toilet tank fill valve to make sure it is working properly.
7. If the tank fill valve is not working properly, replace it with a new one.
8. Turn on the water supply to the toilet.
9. Flush the toilet to test the repair.

Q: How can I fix a toilet that runs constantly?

A: To fix a toilet that runs constantly, follow these steps:

1. Turn off the water supply to the toilet.
2. Flush the toilet to drain the water from the tank.
3. Remove the cap from the toilet tank.
4. Check the toilet tank fill valve to make sure it is not leaking.
5. If the tank fill valve is leaking, replace it with a new one.
6. Check the toilet float to make sure it is not stuck.
7. If the float is stuck, try to unstick it by gently prying it up with a screwdriver.
8. Turn on the water supply to the toilet.
9. Flush the toilet to test the repair.

Q: How can I fix a toilet that makes a gurgling noise?

A: To fix a toilet that makes a gurgling noise, follow these steps:

1. Turn

Replacing a toilet bowl is a relatively simple task that can be completed in a few hours. However, it is important to follow the steps carefully to avoid damaging the toilet or creating a mess.

This guide has provided you with all the information you need to replace your toilet bowl guts. By following these steps, you can save yourself time and money by doing the job yourself.

Here are the key takeaways from this guide:

  • Before you begin, make sure you have all of the necessary tools and materials.
  • Turn off the water supply to the toilet and flush the toilet to drain the water from the bowl.
  • Remove the old toilet bowl by disconnecting the water supply line, the drain line, and the bolts that hold the toilet to the floor.
  • Clean the toilet flange and apply a new gasket.
  • Place the new toilet bowl on the flange and secure it with the bolts.
  • Connect the water supply line and the drain line.
  • Flush the toilet to test for leaks.

By following these steps, you can easily replace your toilet bowl and have a working toilet in no time.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.