How to Replace a Roman Tub Faucet: A Step-by-Step Guide

AvatarByLiana Farrell Faucet Queries

How to Replace a Roman Tub Faucet

Roman tub faucets are a beautiful and elegant addition to any bathroom, but they can be tricky to replace if you’re not sure what you’re doing. In this article, we’ll walk you through the process of replacing a Roman tub faucet, step-by-step. We’ll cover everything from removing the old faucet to installing the new one, and we’ll provide tips and tricks to help you get the job done right.

So if you’re ready to give your bathroom a facelift, read on for all the information you need to know about replacing a Roman tub faucet.

What You’ll Need

Before you get started, gather all the tools and materials you’ll need to complete the job. Here’s a list of what you’ll need:

  • New Roman tub faucet
  • Tape measure
  • Pencil
  • Combination or socket wrench
  • Pliers
  • Pipe wrench
  • Penetrating oil
  • Rags
  • Plumbing putty
  • Silicone sealant
  • Caulk gun

Step-by-Step Instructions

1. Turn off the water supply to the faucet. This is usually done by turning off the main water valve located near the water meter. Once the water is turned off, open the faucet to drain any remaining water from the lines.
2. Remove the old faucet. Start by removing the decorative cap on the end of the faucet stem. This cap is usually held in place by a small screw or nut. Once the cap is removed, you’ll see the faucet stem. Use a wrench to loosen the nuts that hold the faucet stem in place. Be careful not to damage the threads on the stem.
3. Disconnect the water supply lines. There will be two water supply lines connected to the faucet. These lines are usually copper or plastic. Use a wrench to loosen the nuts that connect the lines to the faucet. Be careful not to damage the threads on the lines.
4. Remove the old faucet. Once the water supply lines are disconnected, you can remove the old faucet. Simply lift it up and out of the sink.
5. Install the new faucet. Before you install the new faucet, make sure to apply a thin coat of plumber’s putty to the threads of the faucet stem. This will help to create a watertight seal. Then, align the faucet with the holes in the sink and screw it into place. Be careful not to overtighten the faucet, as this could damage the threads.
6. Connect the water supply lines. Connect the water supply lines to the new faucet. Make sure to tighten the nuts securely.
7. Turn on the water supply and test the faucet. Turn on the main water valve and open the faucet to test the new faucet. Make sure that the water is flowing smoothly and that there are no leaks.
8. Apply silicone sealant around the base of the faucet. This will help to prevent water from leaking around the faucet.
9. Caulk around the base of the faucet. This will help to seal the faucet to the sink and create a watertight seal.

That’s it! You’ve now successfully replaced your Roman tub faucet.

Step Instructions Image
1 Turn off the water supply to the faucet.
2 Remove the old faucet by unscrewing the nuts that hold it in place.
3 Install the new faucet by screwing it into place and tightening the nuts.
4 Turn on the water supply to the faucet and check for leaks.

A Roman tub faucet is a type of faucet that is typically found in bathtubs. It is characterized by its long, curved spout and its two handles, which are typically located on either side of the spout. Roman tub faucets are often used in traditional or vintage-style bathrooms.

Replacing a Roman tub faucet is a relatively simple task that can be completed in a few hours. However, it is important to follow the steps carefully in order to avoid damaging the faucet or the plumbing.

In this guide, we will walk you through the process of replacing a Roman tub faucet. We will provide step-by-step instructions and tips to help you complete the project successfully.

Gather the necessary tools and materials

The following tools and materials are required to replace a Roman tub faucet:

  • Tape measure
  • Combination wrench
  • Pliers
  • Penetrating oil
  • New faucet
  • O-rings
  • Washers
  • Pipe sealant

Turn off the water supply to the faucet

The first step is to turn off the water supply to the faucet. This can be done by locating the shut-off valves for the hot and cold water lines to the faucet. These valves are typically located behind the faucet or under the sink.

To turn off the water, turn the valves clockwise until they are closed. Once the water is turned off, you can begin removing the old faucet.

Remove the old faucet

To remove the old faucet, you will need to first remove the escutcheon plates. These plates cover the mounting nuts for the faucet and are typically located on either side of the faucet.

To remove the escutcheon plates, use a flathead screwdriver to pry them up. Once the escutcheon plates are removed, you will see the mounting nuts for the faucet.

Use a combination wrench to loosen the mounting nuts. Be careful not to overtighten the nuts, as this could damage the faucet. Once the nuts are loosened, you can remove the old faucet.

Install the new faucet

To install the new faucet, you will need to first apply a small amount of pipe sealant to the threads of the faucet. This will help to prevent leaks.

Next, insert the faucet into the mounting holes in the sink. Once the faucet is in place, tighten the mounting nuts with a combination wrench.

Be careful not to overtighten the nuts, as this could damage the faucet. Once the nuts are tightened, you can install the escutcheon plates.

Test the faucet

Once the new faucet is installed, you can turn on the water supply to the faucet and test it. Make sure that the faucet is working properly and that there are no leaks.

If there are any leaks, you can tighten the mounting nuts or apply more pipe sealant.

Replacing a Roman tub faucet is a relatively simple task that can be completed in a few hours. By following the steps in this guide, you can easily replace your old faucet with a new one.

Here are some additional tips to help you complete the project successfully:

  • Make sure that you have all of the necessary tools and materials before you begin.
  • Work slowly and carefully to avoid damaging the faucet or the plumbing.
  • If you are not comfortable working with plumbing, you may want to hire a professional to do the job for you.

3. Remove the old faucet

To remove the old faucet, you will need:

  • A wrench
  • A screwdriver
  • A bucket
  • Penetrating oil

1. Turn off the water supply to the faucet.
2. Disconnect the water supply lines from the faucet.
3. Loosen the nuts or screws that hold the faucet to the sink.
4. Remove the faucet from the sink.
5. Inspect the faucet for any damage or wear.

If the faucet is damaged, you will need to replace it. If the faucet is not damaged, you can clean it and reinstall it.

4. Install the new faucet

To install the new faucet, you will need:

  • A new faucet
  • A wrench
  • A screwdriver
  • A bucket
  • Penetrating oil

1. Apply pipe sealant to the threads of the new faucet.
2. Attach the faucet to the sink.
3. Tighten the nuts or screws that hold the faucet to the sink.
4. Turn on the water supply to the faucet.
5. Check for leaks.

If you have any problems installing the new faucet, you can contact a plumber for help.

Replacing a Roman tub faucet is a relatively simple task that can be completed in a few hours. By following these steps, you can save money and get the job done right.

Here are some additional tips for replacing a Roman tub faucet:

  • Make sure to turn off the water supply to the faucet before you begin work.
  • Disconnect the water supply lines from the faucet before you remove it.
  • Use a wrench to loosen the nuts or screws that hold the faucet to the sink.
  • Apply pipe sealant to the threads of the new faucet before you attach it to the sink.
  • Tighten the nuts or screws that hold the faucet to the sink securely.
  • Turn on the water supply to the faucet and check for leaks.

If you have any questions or concerns about replacing a Roman tub faucet, you can contact a plumber for help.

How To Replace Roman Tub Faucet?

Q: What tools do I need to replace a Roman tub faucet?

A: You will need the following tools:

  • A Phillips head screwdriver
  • A flathead screwdriver
  • A crescent wrench
  • A basin wrench
  • A tape measure
  • A pencil
  • A new Roman tub faucet

Q: How do I remove the old faucet?

A: 1. Turn off the water supply to the faucet.
2. Remove the drain plug from the bottom of the tub.
3. Disconnect the hot and cold water supply lines from the back of the faucet.
4. Remove the screws that hold the faucet to the tub.
5. Pull the faucet straight up and out of the tub.

Q: How do I install the new faucet?

A: 1. Apply a thin coat of plumber’s putty to the threads of the new faucet.
2. Insert the faucet into the hole in the tub.
3. Hand-tighten the screws that hold the faucet to the tub.
4. Connect the hot and cold water supply lines to the back of the faucet.
5. Turn on the water supply to the faucet.
6. Check for leaks.

Q: What are some common problems with Roman tub faucets?

A: Some common problems with Roman tub faucets include:

  • Leaking faucets
  • Clogged faucets
  • Faucets that don’t turn on or off properly
  • Faucets that drip

Q: How can I prevent problems with my Roman tub faucet?

A: You can prevent problems with your Roman tub faucet by:

  • Keeping the faucet clean and free of debris
  • Replacing worn or damaged parts as soon as possible
  • Turning off the water supply to the faucet when not in use
  • Having the faucet serviced regularly

    In this comprehensive guide, we have discussed the steps involved in replacing a Roman tub faucet. We have covered everything from identifying the parts of the faucet to removing the old faucet and installing the new one. We hope that this guide has been helpful and that you are now able to replace your Roman tub faucet with confidence.

Here are some key takeaways from this guide:

  • Before you begin, make sure that you have the proper tools and materials.
  • Identify the parts of the faucet and understand how they work together.
  • Turn off the water supply to the faucet and drain the water from the tub.
  • Remove the old faucet by unscrewing the mounting nuts and washers.
  • Install the new faucet by following the manufacturer’s instructions.
  • Turn on the water supply and test the faucet to make sure that it is working properly.

We hope that this guide has been helpful and that you are now able to replace your Roman tub faucet with confidence.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.