How to Replace a Kohler Shower Faucet (Step-by-Step Guide)

How to Replace a Kohler Shower Faucet

Your Kohler shower faucet is one of the most important parts of your bathroom. It’s what you use to get clean, and it can make or break your shower experience. If your faucet is old, leaky, or just not working the way it should, it’s time to replace it.

Replacing a Kohler shower faucet is a relatively simple task that can be completed in just a few hours. In this guide, we’ll walk you through the process step-by-step, so you can have a new faucet up and running in no time.

We’ll cover everything you need to know, from choosing the right faucet to removing the old one and installing the new one. We’ll also provide some tips on how to make the job go smoothly.

So if you’re ready to give your shower a makeover, read on for all the information you need to know about replacing a Kohler shower faucet.

Step	Instructions	Image
1	Turn off the water supply to the shower faucet.
2	Remove the old shower faucet by unscrewing the nuts that hold it in place.
3	Install the new shower faucet by screwing it into place.
4	Turn on the water supply to the shower faucet and test it to make sure it is working properly.

How To Replace a Kohler Shower Faucet?

Tools and Materials Needed

To replace a Kohler shower faucet, you will need the following tools and materials:

• Adjustable wrench
• Pliers
• Tape measure
• Combination/socket wrench
• Penetrating oil
• New shower faucet
• New O-rings
• New washers
• Plumber’s putty
• Pipe sealant
• Caulking gun
• Rags

Step-by-Step Instructions

1. Shut off the water supply. Before you begin any work on your shower faucet, you need to shut off the water supply to the shower. This is usually done by turning a valve located near the water heater. Once the water is turned off, you can proceed with the next steps.
2. Remove the old faucet. The next step is to remove the old faucet. To do this, you will need to first remove the escutcheon plate that covers the mounting nuts. This plate is usually held in place by two screws. Once the screws are removed, you can pry the escutcheon plate off with a flathead screwdriver.

Next, you will need to remove the mounting nuts that hold the faucet in place. These nuts are usually located on the underside of the faucet. To remove them, you will need to use an adjustable wrench or a socket wrench. Once the nuts are removed, you can lift the faucet off of the shower wall.

3. Install the new faucet. To install the new faucet, you will need to first attach the escutcheon plate to the shower wall. This is usually done by using screws or adhesive. Once the escutcheon plate is in place, you can install the new faucet. To do this, you will need to align the faucet with the mounting holes in the escutcheon plate. Then, you will need to insert the mounting nuts and tighten them with an adjustable wrench or a socket wrench.

4. Turn on the water supply and test the faucet. Once the new faucet is installed, you can turn on the water supply and test the faucet. Make sure that the faucet is working properly and that there are no leaks. If there are any leaks, you can tighten the mounting nuts or apply more plumber’s putty.

Replacing a Kohler shower faucet is a relatively simple task that can be completed in a few hours. By following these step-by-step instructions, you can easily replace your old faucet with a new one.

Here are some additional tips for replacing a Kohler shower faucet:

• Make sure that you have the right tools and materials before you begin.
• Work slowly and carefully to avoid damaging the new faucet.
• If you are not comfortable working with plumbing, you may want to hire a professional to do the job for you.

Replacing a Kohler shower faucet is a great way to improve the look and function of your bathroom. By following these step-by-step instructions, you can easily complete the task yourself.

How to Replace a Kohler Shower Faucet

Kohler shower faucets are known for their durability and performance, but even the best faucets can eventually wear out and need to be replaced. If your Kohler shower faucet is leaking, dripping, or not working properly, it’s time to take action and replace it.

Replacing a Kohler shower faucet is a relatively straightforward task, but it does require some basic plumbing skills. In this guide, we’ll walk you through the process of replacing a Kohler shower faucet, step-by-step.

Tools and Materials

Before you begin, gather the following tools and materials:

• Replacement Kohler shower faucet
• Tape measure
• Combination wrench
• Pliers
• Penetrating oil
• Replacement washers and O-rings
• New water supply lines
• Bucket
• Gloves
• Safety glasses

Step 1: Shut off the water supply

The first step is to shut off the water supply to the shower faucet. This can usually be done by turning off the main water valve located at the water meter. Once the water supply is turned off, you can begin to remove the old faucet.

Step 2: Remove the old faucet

To remove the old faucet, you will need to first remove the escutcheon plate. The escutcheon plate is the decorative cover that surrounds the faucet. It is usually held in place by two screws. Once the screws are removed, you can carefully pry the escutcheon plate off of the faucet.

Next, you will need to remove the faucet handles. The handles are usually held in place by a set screw. Use a Phillips head screwdriver to loosen the set screw and remove the handles.

Now you can begin to remove the faucet body. The faucet body is held in place by two bolts. Use a combination wrench to loosen the bolts and remove the faucet body.

Step 3: Install the new faucet

To install the new faucet, you will need to reverse the steps you took to remove the old faucet. First, install the faucet body. Then, install the handles. Finally, install the escutcheon plate.

Once the new faucet is installed, you can turn on the water supply and test the faucet to make sure it is working properly.

Troubleshooting Tips

If your new Kohler shower faucet is not working properly, there are a few things you can check:

• Make sure that the water supply is turned on.
• Check the faucet handles to make sure they are turned on.
• Check the faucet body to make sure it is properly connected to the water supply lines.
• Check the O-rings and washers to make sure they are properly installed.

If you have checked all of these things and the faucet is still not working properly, you may need to contact a qualified plumber for assistance.

Additional Resources

For more information on how to replace a Kohler shower faucet, you can refer to the following resources:

• [Kohler’s website](https://www.kohler.com/us/how-to-install-a-shower-faucet/)
• [The Home Depot](https://www.homedepot.com/c/how-to-install-a-shower-faucet-HD10005150)
• [DIY Network](https://www.diynetwork.com/how-to/plumbing/how-to-replace-a-shower-faucet)

  How To Replace Kohler Shower Faucet?

Q: What tools do I need to replace a Kohler shower faucet?

A: You will need the following tools:

• A Phillips head screwdriver
• A flathead screwdriver
• A basin wrench
• A tape measure
• A hacksaw
• A pipe wrench
• A bucket
• Plumbing sealant

Q: How do I remove the old faucet?

A: 1. Turn off the water supply to the faucet.
2. Remove the escutcheon plate from around the faucet.
3. Unscrew the mounting nuts that hold the faucet to the wall.
4. Use a basin wrench to loosen the water supply lines.
5. Remove the faucet from the wall.

Q: How do I install the new faucet?

A: 1. Apply a bead of plumbing sealant to the threads of the new faucet.
2. Insert the faucet into the wall and tighten the mounting nuts.
3. Connect the water supply lines to the faucet.
4. Replace the escutcheon plate.
5. Turn on the water supply to the faucet and test it for leaks.

Q: What if I have trouble removing the old faucet?

A: If you are having trouble removing the old faucet, you can try using a heat gun or a torch to loosen the sealant. Be careful not to damage the faucet or the surrounding area.

Q: What if I have trouble installing the new faucet?

A: If you are having trouble installing the new faucet, you can contact a qualified plumber for help.

Q: How often should I replace my shower faucet?

A: Shower faucets should be replaced every 10 to 15 years. However, if you notice any leaks, drips, or other problems with your faucet, it should be replaced sooner.

Replacing a Kohler shower faucet is a relatively simple task that can be completed in about an hour. By following the steps outlined in this guide, you can save yourself the time and money of hiring a plumber.

Here are the key takeaways from this article:

• Before you begin, make sure you have the necessary tools and materials.
• Turn off the water supply to the faucet and drain the water from the pipes.
• Remove the old faucet by unscrewing the mounting nuts and washers.
• Install the new faucet by following the manufacturer’s instructions.
• Turn on the water supply and test the faucet to make sure it is working properly.

By following these steps, you can easily replace your Kohler shower faucet and enjoy a new, working faucet in no time.