How to Replace a Camper Toilet (The Complete Guide)

AvatarByLiana Farrell Toilet Queries

How to Replace a Camper Toilet

Camper toilets are a necessity for any RVer, but they can also be a source of trouble. If your camper toilet is leaking, overflowing, or just not working properly, it’s time to replace it. Replacing a camper toilet is a relatively simple task, but it’s important to do it correctly the first time. In this article, we’ll walk you through the process of replacing a camper toilet, step-by-step. We’ll also provide tips on how to choose the right toilet for your camper and how to maintain it properly.

So if you’re ready to learn how to replace a camper toilet, read on!

Step Instructions Image
1 Turn off the water supply to the toilet.
2 Disconnect the water line from the toilet.
3 Remove the toilet seat.
4 Disconnect the toilet from the floor.
5 Remove the old toilet.
6 Install the new toilet.
7 Reconnect the water line and the toilet seat.
8 Turn on the water supply to the toilet.

Preparing for the Replacement

Replacing a camper toilet is a relatively simple task, but it does require some preparation. Before you get started, gather the following tools and materials:

  • A new toilet
  • A toilet flange
  • A wax ring
  • A plumber’s putty
  • A hacksaw
  • A screwdriver
  • A wrench
  • A bucket
  • A pair of gloves
  • A shop vac

Gather the necessary tools and materials

The first step is to gather all of the necessary tools and materials. This will include the following:

  • A new toilet
  • A toilet flange
  • A wax ring
  • A plumber’s putty
  • A hacksaw
  • A screwdriver
  • A wrench
  • A bucket
  • A pair of gloves
  • A shop vac

Disconnect the water and sewer lines

Once you have gathered all of your tools and materials, you can begin by disconnecting the water and sewer lines. To do this, you will need to locate the water supply line and the sewer line. The water supply line is usually located on the back of the toilet, and the sewer line is usually located on the bottom of the toilet.

To disconnect the water supply line, you will need to turn off the water to the camper. Once the water is turned off, you can use a wrench to loosen the nut that connects the water supply line to the toilet. Once the nut is loosened, you can disconnect the water supply line from the toilet.

To disconnect the sewer line, you will need to use a hacksaw to cut the pipe that connects the toilet to the sewer line. Once the pipe is cut, you can remove the toilet from the camper.

Remove the old toilet

Once you have disconnected the water and sewer lines, you can remove the old toilet. To do this, you will need to lift the toilet up and out of the camper. Be careful not to damage the floor or the sewer line.

Once the old toilet is removed, you can clean the area where the toilet was installed. This will help to prevent any leaks when you install the new toilet.

Installing the New Toilet

Now that you have removed the old toilet, you can begin installing the new toilet. To do this, you will need to follow these steps:

Choose the right toilet for your camper

The first step is to choose the right toilet for your camper. There are a few things to consider when choosing a toilet, such as the size, the weight, and the features.

  • Size: The size of the toilet is important because you need to make sure that it will fit in your camper. Most camper toilets are around 24 inches wide and 17 inches deep.
  • Weight: The weight of the toilet is also important because you need to make sure that it can support the weight of the camper. Most camper toilets weigh around 50 pounds.
  • Features: The features of the toilet are important because you need to make sure that it has the features that you need. Some features that you may want to consider include a flushing mechanism, a seat cover, and a built-in bidet.

Level the toilet and attach it to the floor

Once you have chosen the right toilet for your camper, you can begin installing it. The first step is to level the toilet. To do this, you will need to use a level to make sure that the toilet is level in both directions. Once the toilet is level, you can attach it to the floor.

To attach the toilet to the floor, you will need to use a plumber’s putty. Apply a bead of plumber’s putty around the base of the toilet, and then press the toilet down onto the floor. Make sure that the toilet is firmly attached to the floor.

Connect the water and sewer lines

Once the toilet is attached to the floor, you can connect the water and sewer lines. To connect the water supply line, you will need to use a new nut to connect the water supply line to the toilet. Once the nut is tightened, you can turn on the water to the camper.

To connect the sewer line, you will need to use a new gasket to connect the sewer line to the toilet. Once the gasket is in place, you can connect the sewer line to the toilet.

Test the toilet

Once the toilet is installed, you can test it to make sure that it is working properly. To do this, you will need to flush the toilet. The toilet should flush properly and there should be no leaks.

If the toilet is not working properly, you may need to adjust the height of the toilet or the position of the water supply line. You

How To Replace A Camper Toilet?

Replacing a camper toilet is a relatively simple task that can be completed in a few hours. However, it is important to follow the steps carefully to ensure that the job is done correctly.

Tools and Materials

  • Replacement toilet
  • Toilet flange
  • Wax ring
  • Silicone sealant
  • Pliers
  • Tape measure
  • Level
  • Screwdriver
  • Hammer
  • Bucket
  • Gloves
  • Safety glasses

Step 1: Remove the Old Toilet

The first step is to remove the old toilet. To do this, you will need to disconnect the water supply line and the sewer line.

1. Turn off the water supply to the toilet. This is usually located at the back of the toilet, near the floor.
2. Disconnect the water supply line. The water supply line is a plastic or copper pipe that connects to the back of the toilet. To disconnect it, you will need to unscrew the nut that holds it in place.
3. Disconnect the sewer line. The sewer line is a PVC pipe that connects to the bottom of the toilet. To disconnect it, you will need to unscrew the nut that holds it in place.
4. Remove the toilet bolts. The toilet bolts are located on the bottom of the toilet. To remove them, you will need to use a pliers to loosen the nuts that hold them in place.
5. Lift the toilet off the floor. Once the toilet bolts are removed, you can lift the toilet off the floor. Be careful not to drop the toilet, as it is heavy.

Step 2: Prepare the New Toilet

Once the old toilet is removed, you can prepare the new toilet. To do this, you will need to install the toilet flange and wax ring.

1. Install the toilet flange. The toilet flange is a metal ring that sits on the floor and supports the toilet. To install it, you will need to measure the distance from the back of the toilet to the wall. Then, you will need to cut a piece of plywood to that size. The plywood will serve as a base for the toilet flange.
2. Apply the wax ring. The wax ring is a rubber ring that creates a seal between the toilet and the floor. To apply it, you will need to spread a thin layer of wax around the bottom of the toilet.

Step 3: Install the New Toilet

Now that the new toilet is prepared, you can install it. To do this, you will need to follow these steps:

1. Place the toilet on the toilet flange. Make sure that the toilet is centered on the flange and that the bolts are aligned with the holes in the toilet.
2. Insert the bolts through the holes in the toilet and tighten them with a screwdriver.
3. Connect the water supply line and the sewer line.
4. Turn on the water supply to the toilet.
5. Flush the toilet to make sure that it is working properly.

Step 4: Clean Up

Once the new toilet is installed, you can clean up the mess. To do this, you will need to:

1. Wipe up any water or debris that was spilled during the installation process.
2. Remove the plywood that was used as a base for the toilet flange.
3. Throw away any old materials that were used during the installation process.

Replacing a camper toilet is a relatively simple task that can be completed in a few hours. However, it is important to follow the steps carefully to ensure that the job is done correctly. By following these steps, you can easily replace your camper toilet and get back to enjoying your camping trips.

Additional Tips

  • If you are not comfortable working with plumbing, you may want to hire a professional to replace your camper toilet.
  • Make sure that you have the right tools and materials before you start the project.
  • Take your time and work carefully to avoid damaging the toilet or the floor.
  • Dispose of any old materials properly.

Maintaining Your Camper Toilet

Maintaining your camper toilet is important to keep it working properly and to prevent problems. Here are a few tips for maintaining your camper toilet:

  • Clean the toilet regularly. The best way to prevent problems with your camper toilet is to clean it regularly. This means cleaning the bowl, the seat, and the tank. You should also clean the flush valve and the water supply line.
  • Flush the toilet with a vinegar and baking soda solution every month. This will help to keep the toilet clean and free of bacteria. To do this, mix equal parts vinegar and baking soda in a bucket. Then, pour the solution into the toilet bowl and

    How To Replace A Camper Toilet?

Q: What tools do I need to replace a camper toilet?

A: You will need the following tools:

  • A screwdriver
  • A wrench
  • A pair of pliers
  • A bucket
  • A hose
  • A new toilet

Q: How do I remove the old toilet?

A: To remove the old toilet, follow these steps:

1. Turn off the water supply to the toilet.
2. Flush the toilet to empty the bowl.
3. Remove the toilet tank lid.
4. Locate the water supply line to the toilet.
5. Disconnect the water supply line by turning the shut-off valve counterclockwise.
6. Remove the nuts that hold the toilet to the floor.
7. Lift the toilet up and away from the floor.

Q: How do I install the new toilet?

A: To install the new toilet, follow these steps:

1. Place the new toilet on the floor in the same location as the old toilet.
2. Connect the water supply line to the new toilet.
3. Secure the toilet to the floor with the nuts that you removed from the old toilet.
4. Turn on the water supply to the toilet.
5. Flush the toilet to check for leaks.

Q: What are some common problems with camper toilets?

A: Some common problems with camper toilets include:

  • A clogged toilet
  • A leaking toilet
  • A toilet that won’t flush

Q: How do I fix a clogged toilet?

A: To fix a clogged toilet, you can try the following methods:

  • Use a plunger to clear the clog.
  • Use a toilet auger to clear the clog.
  • Pour a bottle of liquid plumber down the drain to dissolve the clog.

Q: How do I fix a leaking toilet?

A: To fix a leaking toilet, you can try the following methods:

  • Tighten the nuts that hold the toilet to the floor.
  • Replace the toilet gasket.
  • Repair or replace the toilet flapper.

Q: How do I fix a toilet that won’t flush?

A: To fix a toilet that won’t flush, you can try the following methods:

  • Make sure that the water supply to the toilet is turned on.
  • Check the toilet flapper to make sure that it is not stuck.
  • Clean the toilet drain with a plunger or a toilet auger.

Q: What are some tips for maintaining a camper toilet?

A: Here are some tips for maintaining a camper toilet:

  • Flush the toilet regularly to prevent clogs.
  • Clean the toilet bowl with a toilet brush and a cleaning solution.
  • Deodorize the toilet with a toilet bowl cleaner or a baking soda and vinegar solution.
  • Drain the water from the toilet tank every few weeks to prevent bacteria growth.

    Replacing a camper toilet is a relatively straightforward task, but it is important to follow the steps carefully to ensure that the new toilet is installed correctly and that you do not damage the camper. By following the steps outlined in this article, you can easily replace your camper toilet and get back to enjoying your camping adventures.

Here are the key takeaways from this article:

  • Before you begin, make sure you have all of the necessary tools and materials.
  • Turn off the water supply to the toilet and disconnect the sewage line.
  • Remove the old toilet by disconnecting the water supply line, the sewage line, and the bolts that hold it in place.
  • Clean the area where the toilet was installed.
  • Install the new toilet by following the manufacturer’s instructions.
  • Connect the water supply line, the sewage line, and the bolts that hold the toilet in place.
  • Turn on the water supply and test the toilet to make sure it is working properly.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.