How To Raise A Toilet?

AvatarByLiana Farrell Toilet Queries

How to Raise a Toilet

Your toilet is one of the most important fixtures in your home, but it can also be one of the most frustrating. If your toilet is too low, it can be difficult to use and even pose a safety hazard. Fortunately, raising a toilet is a relatively simple task that can be completed in just a few steps.

In this article, we will walk you through the process of raising a toilet, step-by-step. We will also provide tips on how to choose the right height for your toilet and how to make sure the job is done correctly.

So if your toilet is too low, don’t despair – read on to learn how to raise it!

How To Raise A Toilet?

| Step | Task | Tools |
|—|—|—|
| 1 | Shut off the water supply to the toilet. | Plumber’s wrench |
| 2 | Remove the toilet tank lid. | Flathead screwdriver |
| 3 | Locate the bolts that hold the toilet to the floor. | 1/2-inch socket wrench and socket |
| 4 | Loosen the bolts and carefully lift the toilet off the floor. | 2×4 board |
| 5 | Place the 2×4 board under the toilet bowl to support it. | Level |
| 6 | Reposition the toilet so that it is level. | Plumber’s putty |
| 7 | Tighten the bolts to secure the toilet to the floor. | Plumber’s putty |
| 8 | Turn on the water supply to the toilet. | Toilet plunger |
| 9 | Flush the toilet to test the seal. | Toilet brush |

How to Raise a Toilet?

Tools and materials you will need

To raise a toilet, you will need the following tools and materials:

  • A hacksaw
  • A plunger
  • A level
  • A measuring tape
  • A pencil
  • A bucket
  • A sponge
  • A new wax ring
  • Silicone sealant
  • A new toilet flange
  • A new toilet seat

Steps to raise a toilet

1. Turn off the water supply to the toilet. This is usually located under the sink or in the basement.
2. Flush the toilet to drain all of the water.
3. Remove the toilet tank lid. There will be two bolts on the back of the tank that hold it in place. Unscrew these bolts and lift the tank off of the bowl.
4. Remove the old wax ring. The wax ring is a rubber gasket that seals the toilet to the floor. It is located around the base of the toilet bowl. You can use a hacksaw to cut the old wax ring in half and then pry it up with a putty knife.
5. Clean the toilet flange. The toilet flange is a metal ring that is attached to the floor and supports the toilet. It is important to clean this area thoroughly to remove any dirt or debris that could prevent the new wax ring from sealing properly.
6. Apply a new wax ring. The new wax ring should be slightly larger than the old one. Apply a generous amount of silicone sealant to the bottom of the new wax ring and then place it around the toilet flange.
7. Position the toilet bowl. Center the toilet bowl over the toilet flange and lower it into place.
8. Secure the toilet bowl. Use the two bolts that you removed from the tank to secure the toilet bowl to the floor. Tighten the bolts until they are snug, but do not overtighten them.
9. Reattach the toilet tank. Place the toilet tank back on the bowl and secure it with the two bolts that you removed earlier. Tighten the bolts until they are snug, but do not overtighten them.
10. Turn on the water supply to the toilet. Flush the toilet to check for leaks. If there are no leaks, you have successfully raised your toilet.

Raising a toilet is a relatively simple task that can be completed in a few hours. By following these steps, you can raise your toilet and ensure that it is properly supported and sealed.

3. Troubleshooting

If you’re having trouble raising your toilet, there are a few things you can check.

  • Make sure the toilet is properly supported. The toilet should be sitting level on a solid surface. If the toilet is not level, it will be difficult to raise it.
  • Check the bolts. The bolts that hold the toilet to the floor should be tight. If the bolts are loose, the toilet may be able to move around, making it difficult to raise.
  • Check the wax ring. The wax ring is a seal that prevents water from leaking from the toilet to the floor. If the wax ring is damaged, it will need to be replaced.
  • Check the water supply line. The water supply line should be connected to the toilet and turned on. If the water supply line is not connected or turned on, the toilet will not fill with water and will be difficult to raise.

If you’ve checked all of these things and you’re still having trouble raising your toilet, you may need to call a plumber.

4. Tips and tricks

Here are a few tips and tricks to help you raise your toilet:

  • Use a plunger to help loosen the bolts that hold the toilet to the floor.
  • Place a piece of wood under the toilet to provide additional support.
  • Use a strap wrench to turn the bolts that hold the toilet to the floor.
  • Have a helper hold the toilet in place while you raise it.

Raising a toilet can be a difficult task, but it’s important to do it correctly to avoid damage to your toilet and your floor. By following these tips and tricks, you can raise your toilet safely and easily.

Raising a toilet is a relatively simple task that can be completed in a few minutes. By following the steps in this guide, you can raise your toilet safely and easily.

If you have any questions or concerns, please consult with a plumber.

How To Raise A Toilet?

  • Q: Why would I want to raise my toilet?

A: There are a few reasons why you might want to raise your toilet.

  • To make it easier for people with disabilities to use. A raised toilet makes it easier for people who have difficulty bending or standing to get on and off the toilet.
  • To create more space under the toilet for storage. Raising the toilet can create more space under the toilet for storage, such as for cleaning supplies or extra toilet paper.
  • To improve the appearance of your bathroom. A raised toilet can give your bathroom a more modern look.
  • Q: How much does it cost to raise a toilet?

The cost of raising a toilet will vary depending on the type of toilet you have and the materials you use. The average cost is between \$100 and \$200.

  • Q: How long does it take to raise a toilet?

Raising a toilet can take anywhere from 1 to 2 hours, depending on the type of toilet you have and the materials you use.

  • Q: What tools do I need to raise a toilet?

You will need the following tools to raise a toilet:

  • A screwdriver
  • A wrench
  • A level
  • A measuring tape
  • A bucket
  • A sponge
  • A pair of gloves
  • What materials do I need to raise a toilet?

You will need the following materials to raise a toilet:

  • A new toilet flange
  • A wax ring
  • A toilet shim kit
  • Silicone sealant
  • Wood blocks
  • How do I raise a toilet?

To raise a toilet, follow these steps:

1. Turn off the water supply to the toilet.
2. Remove the toilet seat.
3. Remove the nuts and bolts that connect the toilet to the floor.
4. Place a bucket under the toilet to catch any water that may leak out.
5. Lift the toilet up and place it on the wood blocks.
6. Apply a bead of silicone sealant around the bottom of the toilet.
7. Place the new toilet flange on top of the wood blocks.
8. Apply a new wax ring to the bottom of the toilet.
9. Lower the toilet onto the flange and tighten the nuts and bolts.
10. Turn on the water supply to the toilet.
11. Replace the toilet seat.

  • What are some common problems with raised toilets?

There are a few common problems that can occur with raised toilets.

  • The toilet may leak. If the toilet is not installed properly, it may leak water from the base. This can be caused by a loose wax ring, a damaged toilet flange, or a crack in the toilet bowl.
  • The toilet may be too high. If the toilet is raised too high, it may be difficult for people to get on and off. This can be especially difficult for people with disabilities.
  • The toilet may be too low. If the toilet is raised too low, it may be difficult to flush. This can cause the toilet to overflow.
  • How can I prevent problems with raised toilets?

To prevent problems with raised toilets, follow these tips:

  • Make sure the toilet is installed properly.
  • Use a new wax ring and a new toilet flange.
  • Tighten the nuts and bolts securely.
  • Test the toilet for leaks before using it.
  • Additional Resources

For more information on how to raise a toilet, you can refer to the following resources:

  • [How to Raise a Toilet](https://www.thespruce.com/how-to-raise-a-toilet-4171337)
  • [How to Raise a Toilet Seat](https://www.familyhandyman.com/plumbing/toilets/how-to-raise-a-toilet-seat/)
  • [How to Raise a Toilet Without Removing the Toilet](https://www.diynetwork.com/how-to/home-improvement/plumbing/how-to-raise-a-toilet-without-removing-the-toilet)

    In this blog post, we have discussed how to raise a toilet. We have covered the steps involved in the process, as well as the tools and materials you will need. We have also provided tips on how to make sure the job is done correctly and safely.

We hope that this blog post has been helpful. If you have any questions, please do not hesitate to contact us.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.