Where to Mount a Toilet Roll Holder
Mount a typical home toilet roll holder on the side wall beside the toilet, with the roll center 26 to 30 inches from the floor and the holder center 8 to 12 inches in front of the toilet’s front edge. The best side is the one a seated user can reach easily without twisting, while keeping the roll clear of knees, cabinet doors, and shower spray.
Use this chart to choose a location before making any holes.
| Situation | Where to Place the Holder | Mounting Approach |
|---|---|---|
| Typical residential bathroom | Adjacent side wall; roll center 26 to 30 inches above the floor and holder center 8 to 12 inches in front of the toilet’s front edge | Wall-mounted holder on a stud, concrete, or drywall |
| Accessible bathroom layout | Side wall; dispenser centerline 7 to 9 inches in front of the toilet’s front edge | Keep the bottom of the holder 15 to 48 inches above the floor. |
| Narrow gap between toilet and vanity | Adjacent wall with a vertical holder, if a horizontal arm will not fit | Vertical, recessed, or freestanding holder |
| Rental or a wall you cannot drill | Next to the toilet on the floor or hooked over the tank | Freestanding or tank-mounted holder |
| Toilet near a shower | Side wall outside the normal splash zone | Wall mount, tank mount, or freestanding holder away from direct spray |
Where a Toilet Roll Holder Works Best
A toilet roll holder normally belongs on the wall next to the toilet, rather than behind it. This location lets you tear paper with one hand while seated and makes roll changes easier.
Choose the closest clear spot for the holder.
Before committing to a location, hold the new holder and a full roll against the wall. Sit on the closed toilet lid or seat and check that you can reach it comfortably. Make sure the roll will not hit:
- A vanity drawer or cabinet door
- Your knee when sitting down
- A toilet tank lid or flush handle
- A shower door, curtain, or towel bar
- A nearby outlet, switch, or wall control
Choose the side that works for the bathroom layout and the people using it. There is no required right-hand or left-hand side in a typical home bathroom.
How to Mount a Toilet Roll Holder Securely
A wall-mounted holder usually attaches to one or two small metal mounting brackets hidden behind the finished holder. The brackets screw to the wall first; then the holder slides or locks onto them with a small setscrew.
Step 1: Choose the Exact Mounting Spot
- Confirm any local plumbing and building-code requirements with the local authority having jurisdiction before installation. This is especially important for an accessible bathroom or a remodel subject to inspection.
- Mark the chosen location for the holder. For a typical home installation, mark the roll center 26 to 30 inches above the floor.
- Plan the holder center 8 to 12 inches in front of the toilet’s front edge.
A toilet paper holder is not built to carry body weight.
Step 2: Identify the Wall and Holder Hardware
Studs, concrete, and drywall are all common mounting surfaces for a toilet roll holder. Confirm the wall construction at the selected location before drilling, because the screws and anchors must match the material.
Most holders use one of these setups:
- Double-post holder: Two concealed brackets support a horizontal spring bar or pivoting arm.
- Single-post holder: One mounting plate supports an open arm. Check that the arm opens toward clear space, not into a vanity.
- Open holder: The roll slides on from one end; mount it so the open end is convenient to load.
- Vertical holder: The roll drops onto a vertical post, useful when wall width is limited.
- Covered or double holder: These need enough clearance for the cover and replacement roll.
For the Kohler K-29250T and K-29251T double holders, Kohler identifies stud, concrete, and drywall mounting as suitable surfaces and provides hardware instructions for each wall type in its installation instructions.
Step 3: Remove the Brackets and Mark the Holes
- Remove the mounting brackets from the holder. On many concealed-mount models, loosen the tiny setscrew on the underside with the included hex key.
- Hold the bracket in the selected position and use a level to make it straight.
- Mark each screw hole with a pencil.
- If your holder includes a paper template, tape it flat to the wall and level it before marking the holes.
- For a Kohler K-29250T double holder, verify that the supplied template matches the product before marking anything.
Check the marks one last time by holding the holder body in place. This helps prevent drilling holes that leave the roll too close to a cabinet or too far from the toilet.
Step 4: Drill the Mounting Holes
Put on eye protection before drilling. Use a drill bit suited to the wall material and the anchor system supplied with the holder.
For Kohler’s K-29250T and K-29251T double holders, the specified hole diameters are 3 mm for a stud, 6 mm for concrete, and 8 mm for drywall. Confirm both the wall surface and the product installation instructions before choosing a bit, since other holders may use different hardware.
Drill straight into the marked locations. Stop if the bit meets unexpected solid metal or another obstruction rather than forcing it through.
Step 5: Install the Correct Anchors and Brackets
Use the anchor type that matches the wall:
- Wood stud: Drive the mounting screws directly into the stud.
- Wood-panel wall: Kohler’s double-holder installation calls for no plugs in a wood-panel wall. Confirm that the mounting surface is actually wood paneling and not thin decorative paneling over drywall.
- Concrete wall: Insert wall anchors into the drilled holes and tap them flush with the wall before installing the bracket screws.
- Drywall: Use butterfly anchors for the Kohler double-holder setup. Fold the anchor wings inward, insert the anchor through the hole, and let the wings open behind the drywall before tightening.
Screw the mounting bracket or brackets firmly to the wall. Check with a level before fully tightening the screws. The bracket should sit flat with no rocking or gap behind it.
Step 6: Attach the Holder and Test It
- Slide or snap the holder body onto the mounting bracket.
- Tighten the setscrew or locking screw that secures the holder to the bracket.
- Install a full roll and pull several sheets to make sure it turns freely.
- Push lightly on the holder from different directions. It should not wobble, shift, or pull away from the wall.
- Check that the roll can be replaced without removing the entire holder.
Toilet Roll Holder Placement for Small and Accessible Bathrooms
Tight Bathrooms and Awkward Wall Space
When there is little room between the toilet and vanity, a vertical holder can fit where a horizontal roll holder cannot. A freestanding holder is another easy choice when drilling is not practical.
A recessed holder saves projection into the room, but it requires opening the wall. Do not cut into a wall cavity unless you know there are no pipes, electrical cables, or structural concerns in that location.
Before buying a recessed or double toilet roll holder, measure the rolls you normally buy. Typical rolls are about 4.5 to 5 inches long and 4.5 to 5 inches in diameter, and oversized rolls may not fit inside every recessed compartment or covered holder.
Mounting behind the toilet is possible in a very tight bathroom, but it is usually less convenient because the user must reach backward.
Accessible Toilet Roll Holder Placement
For an accessible setup, install the holder on the side wall adjacent to the toilet. The dispenser centerline should sit 7 to 9 inches in front of the toilet’s front edge.
Measure the fixture using the correct reference point:
- Mount the toilet paper holder 19 to 26 inches above the floor.
- For the roll center, keep it between 48 and 66 centimeters from the ground.
Use the dispensing outlet as the reference point, and check the actual holder with a roll installed before drilling. Local accessibility and building requirements may be more specific for a particular bathroom, especially in rental, commercial, or permitted-remodel work.
Shower Spray and Grab-Bar Locations
Keep paper away from the shower’s splash area. Even a covered holder can leave the exposed edge of the roll damp if it is directly beside a showerhead or inside a wet-zone corner.
If a proper grab bar is needed, give it its own secure mounting location rather than trying to make the paper holder do two jobs.
How to Check the Finished Installation
Use this quick check after the holder is installed:
- The holder is level when viewed from the front.
- The mounting brackets do not move when the roll is pulled.
- The roll spins freely and can be changed without scraping the wall.
- A seated user can reach the paper without leaning or twisting uncomfortably.
- Cabinet doors, drawers, and shower doors clear the holder.
If the holder loosens, remove it and inspect the brackets and anchors. Tighten loose bracket screws only if the anchor still grips firmly. If drywall is crumbling or an anchor spins, replace it with a suitable drywall anchor or move the holder to a stud; do not keep using a holder that pulls away from the wall.
Frequently Asked Questions
What Side Should a Toilet Roll Holder Be On?
Put it on whichever side of the toilet gives the easiest reach from a seated position. The adjacent side wall is usually best, and either the left or right side can work. Choose the side that avoids a vanity, shower door, or other obstacle.
How Do You Attach a Toilet Paper Holder to a Wall?
Remove the concealed mounting bracket, mark and level its screw holes, drill for the wall material, install the correct anchors, and screw the bracket to the wall. Then slide the holder onto the bracket, tighten its setscrew, load a roll, and test for movement. For Kohler K-29250T and K-29251T holders, drill 3 mm holes in a stud, 6 mm holes in concrete, or 8 mm holes in drywall.
How Do You Mount a Single-Post Toilet Paper Holder?
Mount a single-post holder with its open arm facing the clear direction where you want to load the roll. Secure its single wall bracket firmly, then lock the holder body onto the bracket with its setscrew or fastening screw. Check that the arm and roll do not strike the vanity or wall when the roll is installed.
What Mounting Brackets Are Available for Toilet Paper Holders?
Most wall-mounted holders use concealed single-post or double-post brackets fastened with screws. Some models use exposed brackets, while vertical holders may use a compact single bracket. Freestanding and tank-mounted holders do not need wall brackets at all.
