How to Install a Project Source Toilet [Step-by-Step Guide]

AvatarByLiana Farrell Toilet Queries

How to Install a Project Source Toilet

Installing a new toilet is a relatively simple task that can be completed in a few hours. However, it is important to follow the proper steps to ensure that the toilet is installed correctly and safely. This guide will walk you through the process of installing a Project Source toilet, from start to finish.

Tools and Materials

Before you begin, gather the following tools and materials:

  • Project Source toilet
  • Wax ring
  • Toilet flange
  • Wax toilet ring
  • Toilet bolts
  • Pliers
  • Tape measure
  • Level
  • Combination/socket wrench
  • Penetrating oil
  • Silicone sealant

Step 1: Prepare the Toilet Bowl

The first step is to prepare the toilet bowl. To do this, you will need to remove the old toilet from the floor. If you are replacing an existing toilet, you can skip this step.

1. Turn off the water supply to the toilet. This is usually located behind the toilet, near the floor.
2. Flush the toilet to empty the tank.
3. Remove the nuts that hold the toilet to the floor. These nuts are usually located on the back of the toilet.
4. Lift up on the toilet and carefully remove it from the floor.

Step 2: Install the Toilet Flange

The toilet flange is a metal ring that sits on the floor and supports the toilet bowl. It is important to install the toilet flange correctly to ensure that the toilet is installed securely.

1. Place the toilet flange on the floor in the location where you want to install the toilet.
2. Mark the location of the holes in the flange with a pencil.
3. Drill holes in the floor at the marked locations.
4. Insert the bolts through the holes in the flange and into the floor.
5. Tighten the bolts until the flange is secure.

Step 3: Apply the Wax Ring

The wax ring is a rubber ring that creates a watertight seal between the toilet bowl and the floor. It is important to apply the wax ring correctly to ensure that the toilet is installed properly.

1. Cut the wax ring to the correct size. The wax ring should be slightly larger than the opening in the toilet bowl.
2. Apply a thin layer of petroleum jelly to the inside of the toilet bowl. This will help to prevent the wax ring from sticking to the bowl.
3. Place the wax ring in the opening in the toilet bowl.
4. Center the toilet bowl over the wax ring.

Step 4: Secure the Toilet Bowl

Once the wax ring is in place, you can secure the toilet bowl to the floor. To do this, you will need to use the bolts that came with the toilet.

1. Insert the bolts through the holes in the toilet bowl and into the flange.
2. Tighten the bolts until the toilet bowl is secure.
3. Be careful not to overtighten the bolts, as this could damage the toilet bowl.

Step 5: Connect the Water Supply

The final step is to connect the water supply to the toilet. To do this, you will need to turn on the water supply to the toilet.

1. Locate the water supply line to the toilet. This is usually located behind the toilet, near the floor.
2. Connect the water supply line to the toilet valve.
3. Turn on the water supply to the toilet.

Congratulations! You have now successfully installed a Project Source toilet.

Step Instructions Image
1 Gather your tools and materials. You will need:
2 Turn off the water supply to the toilet.
3 Remove the old toilet.
4 Install the new toilet.
5 Reconnect the water supply to the toilet.
6 Test the toilet to make sure it is working properly.

Installing a Project Source toilet is a relatively simple task that can be completed in about an hour. However, it is important to follow the steps carefully to ensure that the toilet is installed correctly and securely. This guide will walk you through the process of installing a Project Source toilet, step-by-step.

Gather Your Materials

Before you begin, gather all of the materials you will need to install the toilet. This includes:

  • Project Source toilet
  • Wax ring
  • Toilet flange
  • Bolts
  • Washers
  • Pliers
  • Tape measure
  • Level
  • Pencil
  • Screwdriver

Prepare the Toilet Bowl

The first step is to prepare the toilet bowl. To do this, you will need to:

1. Remove the old toilet from the floor.
2. Clean the floor where the toilet will be installed.
3. Apply a bead of plumber’s putty around the base of the toilet bowl.

Install the Toilet Flange

The next step is to install the toilet flange. To do this, you will need to:

1. Measure the distance from the wall to the center of the drain pipe.
2. Cut a piece of PVC pipe to the appropriate length.
3. Insert the PVC pipe into the drain pipe.
4. Attach the toilet flange to the PVC pipe.

Install the Toilet Bowl

Now it is time to install the toilet bowl. To do this, you will need to:

1. Center the toilet bowl over the toilet flange.
2. Apply a bead of plumber’s putty around the base of the toilet bowl.
3. Lower the toilet bowl onto the toilet flange.
4. Secure the toilet bowl to the floor with the bolts and washers.

Connect the Water Supply Line

The final step is to connect the water supply line to the toilet. To do this, you will need to:

1. Turn off the water supply to the toilet.
2. Remove the old water supply line.
3. Connect the new water supply line to the toilet.
4. Turn on the water supply to the toilet.

Installing a Project Source toilet is a relatively simple task that can be completed in about an hour. By following the steps in this guide, you can install your new toilet with confidence.

Additional Tips

Here are a few additional tips that may help you during the installation process:

  • Use a level to make sure that the toilet is installed level.
  • Tighten the bolts evenly to prevent the toilet from rocking.
  • Do not overtighten the bolts, as this could damage the toilet.
  • If you are having trouble getting the toilet to seal properly, you may need to apply more plumber’s putty.
  • If you are not comfortable installing a toilet yourself, you can always hire a professional plumber to do the job for you.

How to Install a Project Source Toilet

Project Source toilets are a popular choice for homeowners because they are affordable and easy to install. This guide will walk you through the process of installing a Project Source toilet, step-by-step.

1. Gather Your Tools and Materials

Before you begin, make sure you have all of the necessary tools and materials on hand. You will need:

  • A new Project Source toilet
  • A toilet flange
  • A wax ring
  • A toilet seat
  • A hacksaw
  • A drill
  • A screwdriver
  • A level
  • A measuring tape
  • Plumbing putty
  • Silicone caulk
  • Gloves
  • Safety glasses

2. Prepare the Toilet Drain

The first step is to prepare the toilet drain. If you are replacing an existing toilet, you will need to remove the old toilet first. To do this, follow these steps:

1. Turn off the water supply to the toilet.
2. Flush the toilet to drain any remaining water.
3. Remove the nuts that hold the toilet to the floor.
4. Lift the toilet off of the floor and set it aside.

Once the old toilet is removed, you can begin preparing the toilet drain. The toilet drain is located in the floor and is a large, round hole. To prepare the drain, you will need to:

1. Clean the drain of any debris.
2. Apply a coat of plumber’s putty around the edge of the drain.
3. Place the toilet flange over the drain.
4. Secure the toilet flange to the floor with bolts.

3. Install the Toilet Flange

The toilet flange is a metal ring that sits on the floor and supports the toilet bowl. To install the toilet flange, follow these steps:

1. Place the toilet flange on the floor where the toilet will be installed.
2. Mark the location of the bolts on the flange with a pencil.
3. Drill holes through the floor at the marked locations.
4. Insert the bolts through the holes in the floor and into the flange.
5. Tighten the bolts until the flange is secure.

4. Attach the Toilet Bowl to the Flange

The toilet bowl is the main part of the toilet. To attach the toilet bowl to the flange, follow these steps:

1. Place the toilet bowl over the flange.
2. Insert the bolts through the holes in the toilet bowl and into the flange.
3. Tighten the bolts until the toilet bowl is secure.

5. Connect the Water Supply

The final step is to connect the water supply to the toilet. To do this, follow these steps:

1. Locate the water supply line to the toilet.
2. Turn off the water supply to the toilet.
3. Connect the water supply line to the toilet.
4. Turn on the water supply to the toilet.

6. Test the Toilet

Once the toilet is installed, you should test it to make sure it is working properly. To do this, follow these steps:

1. Flush the toilet.
2. Check for leaks around the toilet.
3. Check to make sure the toilet is draining properly.

If the toilet is not working properly, you may need to adjust the toilet seat or the water level.

Installing a Project Source toilet is a relatively simple task that can be completed in a few hours. By following these steps, you can install a new toilet that will provide you with years of reliable service.

How to Install a Project Source Toilet

Q: What tools do I need to install a Project Source toilet?

A: You will need the following tools:

  • A Phillips head screwdriver
  • A flathead screwdriver
  • A tape measure
  • A level
  • A pencil
  • A utility knife
  • A hacksaw
  • A plunger
  • A bucket
  • Gloves
  • Safety glasses

Q: What is the first step in installing a Project Source toilet?

A: The first step is to turn off the water supply to the toilet. This can be done by turning the shutoff valve located behind the toilet clockwise. Once the water supply is turned off, you will need to flush the toilet to empty the tank.

Q: What is the next step in installing a Project Source toilet?

A: The next step is to remove the old toilet. To do this, you will need to first remove the nuts that connect the toilet to the floor flange. Once the nuts are removed, you can lift the toilet up and off of the floor flange.

Q: What is the third step in installing a Project Source toilet?

A: The third step is to apply a thin layer of plumber’s putty to the bottom of the new toilet. This will help to create a seal between the toilet and the floor flange.

Q: What is the fourth step in installing a Project Source toilet?

A: The fourth step is to place the new toilet on the floor flange. Once the toilet is in place, you will need to tighten the nuts that connect the toilet to the floor flange.

Q: What is the fifth step in installing a Project Source toilet?

A: The fifth step is to connect the water supply line to the toilet. To do this, you will need to attach the supply line to the water inlet on the back of the toilet.

Q: What is the sixth step in installing a Project Source toilet?

A: The sixth step is to turn on the water supply to the toilet. Once the water supply is turned on, you will need to flush the toilet to check for leaks.

Q: What is the seventh step in installing a Project Source toilet?

A: The seventh step is to adjust the toilet seat. To do this, you will need to loosen the nuts that hold the toilet seat in place. Once the nuts are loosened, you can adjust the toilet seat until it is level.

Q: What is the eighth step in installing a Project Source toilet?

A: The eighth step is to tighten the nuts that hold the toilet seat in place. Once the nuts are tightened, you can test the toilet seat to make sure it is secure.

Q: What are some common problems that can occur when installing a Project Source toilet?

A: Some common problems that can occur when installing a Project Source toilet include:

  • Leaks
  • Toilet not flushing properly
  • Toilet seat not level
  • Toilet seat not secure

Q: How can I troubleshoot problems with my Project Source toilet?

A: If you are experiencing problems with your Project Source toilet, you can troubleshoot the problem by following these steps:

1. Check for leaks. Look under the toilet for any signs of water leaking. If you see water leaking, you will need to tighten the nuts that connect the toilet to the floor flange.
2. Check the toilet flushing mechanism. Make sure that the flapper is closing properly and that the chain is not too long or too short.
3. Check the toilet seat. Make sure that the toilet seat is level and that the nuts that hold the toilet seat in place are tight.
4. Check the toilet seat bolts. Make sure that the toilet seat bolts are tight.

Q: What is the warranty on Project Source toilets?

A: Project Source toilets come with a limited warranty of one year. This warranty covers defects in materials and workmanship.

Q: Where can I find more information about Project Source toilets?

A: You can find more information about Project Source toilets on the Project Source website: https://www.projectsource.com/toilets.

In this blog post, we have discussed how to install a Project Source toilet. We have covered the steps in detail, from preparing the toilet for installation to connecting the water supply and drain. We have also provided tips on how to make the installation process go smoothly.

We hope that this blog post has been helpful. If you have any questions, please do not hesitate to contact us.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.