How To Install American Standard Toilet?

AvatarByLiana Farrell Toilet Queries

How to Install an American Standard Toilet

Installing a new toilet can be a daunting task, but it’s one that’s definitely doable for the average DIYer. With a little planning and preparation, you can have your new toilet up and running in no time.

In this article, we’ll walk you through the steps of installing an American Standard toilet. We’ll cover everything from choosing the right toilet for your bathroom to connecting the water supply and sewer lines. By the end of this article, you’ll be a pro at toilet installation!

So what are you waiting for? Let’s get started!

Step Instructions Images
1 Turn off the water supply to the toilet. Turn off the water supply to the toilet
2 Remove the old toilet. Remove the old toilet
3 Install the new toilet. Install the new toilet
4 Connect the water supply to the toilet. Connect the water supply to the toilet
5 Test the toilet. Test the toilet

Installing an American Standard toilet is a relatively simple task that can be completed in a few hours. However, it is important to follow the steps carefully to ensure that the toilet is installed correctly and that it functions properly.

This guide will walk you through the process of installing an American Standard toilet, from gathering the necessary tools and materials to attaching the toilet to the floor. By following these steps, you can install your new toilet with confidence.

Gather the necessary tools and materials

The following tools and materials are required to install an American Standard toilet:

  • American Standard toilet
  • Wax ring
  • Toilet flange
  • P-trap
  • PVC pipe
  • Combination/hacksaw
  • Tape measure
  • Level
  • Pencil
  • Screwdriver
  • Adjustable wrench
  • Plumber’s putty

Prepare the toilet drain

The first step in installing an American Standard toilet is to prepare the toilet drain. This involves removing the old toilet, cleaning the drain flange, and applying plumber’s putty to the bottom of the toilet flange.

To remove the old toilet, you will need to disconnect the water supply line and the drain line. The water supply line is typically located on the back of the toilet, and the drain line is located on the bottom of the toilet.

Once the water supply line and drain line have been disconnected, you can begin to remove the old toilet. There are two bolts that hold the toilet to the floor. These bolts are located on the back of the toilet, just below the tank.

To remove the bolts, you will need to use a screwdriver. Once the bolts have been removed, you can lift the toilet up and off of the floor.

Once the old toilet has been removed, you can clean the drain flange. The drain flange is a metal ring that is located in the floor. It is used to connect the toilet to the sewer line.

To clean the drain flange, you will need to use a putty knife or a wire brush. Be sure to remove all of the old wax from the drain flange.

Once the drain flange has been cleaned, you can apply plumber’s putty to the bottom of the flange. This will help to create a seal between the toilet and the drain flange.

Attach the toilet to the floor

The next step is to attach the toilet to the floor. To do this, you will need to place the toilet over the drain flange. Then, you will need to align the holes in the toilet with the bolts in the floor.

Once the holes are aligned, you can insert the bolts through the holes in the toilet and into the floor. Then, you can tighten the bolts with a wrench.

Once the bolts have been tightened, you can connect the water supply line and the drain line. The water supply line is typically located on the back of the toilet, and the drain line is located on the bottom of the toilet.

To connect the water supply line, you will need to attach the end of the water supply line to the valve on the back of the toilet. Then, you will need to tighten the connection with a wrench.

To connect the drain line, you will need to attach the end of the drain line to the P-trap. Then, you will need to tighten the connection with a wrench.

Test the toilet

Once the toilet has been installed, you can test it to make sure that it is working properly. To do this, you will need to turn on the water supply line and flush the toilet.

The toilet should fill with water and flush properly. If there are any leaks, you will need to tighten the connections or apply more plumber’s putty.

Once the toilet is working properly, you can enjoy your new bathroom!

Installing an American Standard toilet is a relatively simple task that can be completed in a few hours. By following the steps in this guide, you can install your new toilet with confidence.

Here are a few additional tips for installing an American Standard toilet:

  • Make sure that the toilet is level. If the toilet is not level, it will not function properly.
  • Use plenty of plumber’s putty. Plumber’s putty will help to create a seal between the toilet and the drain flange.
  • Tighten the bolts securely. Make sure that the bolts are tightened securely to prevent the toilet from leaking.
  • Test the toilet before using it. Make sure that the toilet is working properly before using it.

By following these tips, you can install your new American Standard toilet with confidence.

How To Install American Standard Toilet?

Installing an American Standard toilet is a relatively simple task that can be completed in about an hour. However, it is important to follow the steps carefully to ensure that the toilet is installed correctly and that it functions properly.

Tools and Materials

To install an American Standard toilet, you will need the following tools and materials:

  • A new American Standard toilet
  • A toilet flange
  • A wax ring
  • A toilet seat
  • A hacksaw
  • A screwdriver
  • A wrench
  • A plunger
  • Plumbing tape
  • Silicone sealant

Step 1: Remove the Old Toilet

Before you can install a new American Standard toilet, you will need to remove the old toilet. To do this, follow these steps:

1. Turn off the water supply to the toilet.
2. Flush the toilet to drain the water from the tank.
3. Remove the nuts that connect the toilet to the floor flange.
4. Lift the toilet off of the floor flange.
5. Carefully remove the old wax ring from the toilet flange.

Step 2: Prepare the Toilet Flange

The toilet flange is the metal ring that connects the toilet to the drainpipe. It is important to make sure that the toilet flange is in good condition before you install the new toilet. To do this, follow these steps:

1. Clean the toilet flange with a brush and some soapy water.
2. Inspect the toilet flange for any cracks or damage. If the toilet flange is damaged, you will need to replace it.
3. Apply a thin layer of plumber’s putty to the toilet flange.

Step 3: Install the Toilet Flange

Once the toilet flange is prepared, you can install it. To do this, follow these steps:

1. Position the toilet flange over the drain opening.
2. Secure the toilet flange to the floor with screws.
3. Make sure that the toilet flange is level.

Step 4: Connect the Toilet to the Water Supply

The next step is to connect the toilet to the water supply. To do this, follow these steps:

1. Connect the water supply line to the toilet.
2. Turn on the water supply to the toilet.
3. Check for leaks.

Step 5: Install the Toilet Seat

The final step is to install the toilet seat. To do this, follow these steps:

1. Place the toilet seat on the toilet bowl.
2. Secure the toilet seat to the toilet bowl with screws.
3. Adjust the toilet seat so that it is level.

Installing an American Standard toilet is a relatively simple task that can be completed in about an hour. However, it is important to follow the steps carefully to ensure that the toilet is installed correctly and that it functions properly.

If you have any questions about installing an American Standard toilet, you can contact a qualified plumber for assistance.

How to Install an American Standard Toilet

Q: What tools do I need to install an American Standard toilet?

A: You will need the following tools:

  • A hacksaw
  • A plunger
  • A screwdriver
  • A wrench
  • A level
  • A pencil
  • A measuring tape

Q: How do I prepare the toilet flange for installation?

A: The toilet flange is the metal ring that the toilet bowl sits on. To prepare the flange, you will need to:

1. Remove the old toilet.
2. Clean the flange with a wire brush.
3. Apply a thin coat of plumber’s putty around the flange.

Q: How do I install the toilet bowl?

A: To install the toilet bowl, you will need to:

1. Place the toilet bowl on the flange.
2. Align the holes in the toilet bowl with the bolts on the flange.
3. Insert the bolts through the holes in the toilet bowl and tighten them with a wrench.
4. Connect the water supply line to the toilet bowl.
5. Connect the drain line to the toilet bowl.

Q: How do I install the toilet seat?

A: To install the toilet seat, you will need to:

1. Place the toilet seat on the toilet bowl.
2. Align the holes in the toilet seat with the bolts on the toilet bowl.
3. Insert the bolts through the holes in the toilet seat and tighten them with a screwdriver.

Q: What is the best way to seal around the toilet?

A: The best way to seal around the toilet is to use a silicone sealant. Apply a thin coat of sealant around the base of the toilet and allow it to dry completely.

Q: How do I adjust the height of the toilet seat?

A: To adjust the height of the toilet seat, you will need to:

1. Remove the old toilet seat.
2. Inspect the toilet bowl for mounting bolts.
3. If there are no mounting bolts, you will need to drill holes in the toilet bowl and install mounting bolts.
4. Attach the new toilet seat to the mounting bolts.

Q: What is the best way to clean an American Standard toilet?

A: The best way to clean an American Standard toilet is to:

1. Use a toilet brush to scrub the inside of the toilet bowl.
2. Pour a cup of white vinegar into the toilet bowl and let it sit for 30 minutes.
3. Scrub the toilet bowl again with the toilet brush.
4. Flush the toilet bowl to rinse away the vinegar.

Q: What is the best way to prevent toilet clogs?

A: The best way to prevent toilet clogs is to:

1. Don’t flush anything other than toilet paper and human waste down the toilet.
2. Use a plunger to clear small clogs.
3. Call a plumber to clear large clogs.

In this blog post, we have discussed the steps involved in installing an American Standard toilet. We have provided a detailed overview of the process, as well as tips and tricks to help you get the job done correctly.

We hope that this information has been helpful and that you are now feeling more confident about installing your own American Standard toilet. If you have any questions or concerns, please do not hesitate to contact us. We would be happy to help you out.

Here are some key takeaways from this blog post:

  • Before you begin, make sure that you have all of the necessary tools and materials.
  • Carefully follow the instructions in the installation manual.
  • Be sure to test the toilet to make sure that it is working properly before you install the seat.
  • If you have any questions or concerns, please do not hesitate to contact a professional.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.