How to Change a Faucet in Your Bathroom (Step-by-Step Guide)

AvatarByLiana Farrell Faucet Queries

How to Change a Faucet in Your Bathtub

Your bathtub faucet is one of the most important fixtures in your bathroom. It’s used for everything from washing your hands to taking a bath, so it’s important to make sure it’s working properly. If your faucet is leaking or dripping, it’s time to replace it.

Changing a bathtub faucet is a relatively simple DIY project that can be completed in a few hours. In this article, we’ll walk you through the steps of how to change a bathtub faucet, from start to finish. We’ll also provide tips on choosing the right faucet for your bathroom and how to install it properly.

So if you’re ready to learn how to change a bathtub faucet, read on!

Step Instructions Image
1 Turn off the water supply to the faucet.
2 Remove the old faucet by unscrewing the nuts that hold it in place.
3 Install the new faucet by screwing it into place and tightening the nuts.
4 Turn on the water supply to the faucet and test it to make sure it is working properly.

A bathtub faucet is a critical part of your bathroom, and it’s important to know how to change it if it breaks. This guide will walk you through the process of replacing a bathtub faucet, step-by-step.

We’ll cover everything from gathering your tools and materials to turning off the water supply. We’ll also provide tips on how to choose the right faucet for your bathtub and how to install it properly.

By the end of this guide, you’ll be able to replace a bathtub faucet like a pro.

Gather Your Tools and Materials

The following tools and materials are required to change a bathtub faucet:

  • Adjustable wrench
  • Pliers
  • Penetrating oil
  • New faucet
  • Washers and nuts
  • Pipe sealant
  • Plumbing tape

Turn Off the Water Supply

The first step is to turn off the water supply to the bathtub. This will prevent any water from spilling out when you start working on the faucet.

To turn off the water supply, locate the shut-off valve for the bathtub. This valve is typically located near the bathtub, underneath the sink, or in the basement.

Once you’ve located the shut-off valve, turn it clockwise until it is completely closed. This will stop the flow of water to the bathtub.

Remove the Old Faucet

Now that the water supply is turned off, you can start removing the old faucet.

To do this, you’ll need to first remove the escutcheon plate. This is the decorative cover that surrounds the faucet.

The escutcheon plate is typically held in place by two screws. Locate these screws and unscrew them.

Once the screws are removed, the escutcheon plate will come loose. You can then remove it by carefully prying it up with a flathead screwdriver.

Now that the escutcheon plate is removed, you can see the nuts that hold the faucet in place. These nuts are typically located on the back of the faucet.

Use an adjustable wrench to loosen the nuts. Be careful not to overtighten them, as this could damage the faucet.

Once the nuts are loosened, you can remove the faucet by pulling it straight out.

Install the New Faucet

Now that the old faucet is removed, you can install the new one.

To do this, you’ll need to first attach the new faucet to the sink. This is done by using the washers and nuts that came with the faucet.

Once the faucet is attached to the sink, you can turn on the water supply and test it to make sure that it’s working properly.

Tips for Choosing the Right Faucet

When choosing a new faucet for your bathtub, there are a few things to keep in mind.

First, consider the style of your bathroom. Do you want a traditional faucet or a more modern one?

Second, think about the features that you want in a faucet. Do you want a faucet with a single handle or a double handle? Do you want a faucet with a built-in soap dispenser?

Finally, consider your budget. Faucets can range in price from a few dollars to a few hundred dollars.

How to Install a Faucet

Installing a faucet is a relatively simple task, but it is important to follow the steps carefully to avoid any mistakes.

To install a faucet, you will need the following tools:

  • Adjustable wrench
  • Pliers
  • Penetrating oil
  • New faucet
  • Washers and nuts
  • Pipe sealant
  • Plumbing tape

1. Turn off the water supply to the bathtub.
2. Remove the old faucet.
3. Attach the new faucet to the sink.
4. Turn on the water supply and test the faucet.

Here are the steps in more detail:

1. Turn off the water supply to the bathtub. This can be done by turning the shut-off valve located near the bathtub clockwise until it is closed.
2. Remove the old faucet. To do this, you will need to first remove the escutcheon plate. This is the decorative cover that surrounds the faucet. The escutcheon plate is typically held in place by two screws. Locate these screws and unscrew them. Once the screws are removed, the escutcheon plate will come loose. You can then remove it by carefully prying it up with a flathead screwdriver.
3. Attach the new faucet to the sink. This is done by using the washers and nuts that came with the faucet. First, apply a small amount of pipe sealant to the threads of the faucet. This will help to prevent leaks. Next, attach the faucet to the sink using the washers and nuts. Be sure to tighten the nuts securely, but do not over

How to Change a Faucet in a Bathtub

Changing a faucet in a bathtub is a relatively simple task that can be completed in about an hour. However, it is important to follow the steps carefully to avoid damaging the faucet or the sink.

Tools and Materials

To change a faucet in a bathtub, you will need the following tools and materials:

  • Adjustable wrench
  • Pipe wrench
  • Penetrating oil
  • Pliers
  • Tape measure
  • Combination or socket wrench
  • New faucet
  • Plumbing tape
  • Pipe sealant
  • Silicone caulk
  • Rags
  • Safety glasses

Step 1: Disconnect the Old Faucet

The first step is to disconnect the old faucet from the water supply lines. To do this, you will need to locate the shut-off valves for the hot and cold water lines. These valves are usually located behind the faucet or under the sink.

Turn off the shut-off valves and then drain the water from the faucet by turning on the faucet and letting the water run until it stops.

Once the water has been drained, you can begin to disconnect the faucet from the water supply lines. To do this, you will need to use a wrench to loosen the nuts that connect the faucet to the water supply lines.

Once the nuts have been loosened, you can pull the faucet away from the sink. Be careful not to damage the sink or the faucet.

Step 2: Remove the Escutcheon Plate

The escutcheon plate is a decorative cover that hides the screws that hold the faucet to the sink. To remove the escutcheon plate, you will need to use a flathead screwdriver to pry it up.

Once the escutcheon plate has been removed, you will see the screws that hold the faucet to the sink.

Step 3: Loosen the Faucet Screws

Use a Phillips head screwdriver to loosen the screws that hold the faucet to the sink. Be careful not to strip the screws.

Once the screws have been loosened, you can pull the faucet away from the sink.

Step 4: Remove the Faucet Stem

The faucet stem is the part of the faucet that controls the flow of water. To remove the faucet stem, you will need to use a faucet wrench to loosen the nut that holds it in place.

Once the nut has been loosened, you can pull the faucet stem out of the faucet body.

Step 5: Clean the Faucet Body

Use a rag to clean the faucet body. Be sure to remove any dirt or debris that may be stuck in the threads.

Step 6: Apply Pipe Sealant

Apply a small amount of pipe sealant to the threads of the new faucet. This will help to prevent leaks.

Step 7: Insert the New Faucet

Insert the new faucet into the faucet body. Be sure to align the holes in the faucet with the holes in the faucet body.

Step 8: Connect the Faucet to the Water Supply Lines

Connect the faucet to the water supply lines using the nuts that you removed in Step 1. Be sure to tighten the nuts until they are snug.

Step 9: Replace the Escutcheon Plate

Replace the escutcheon plate by pressing it down onto the faucet.

Step 10: Turn on the Shut-Off Valves

Turn on the shut-off valves to restore water to the faucet.

Step 11: Test the Faucet

Turn on the faucet and check for leaks. If there are no leaks, you have successfully changed the faucet in your bathtub.

Changing a faucet in a bathtub is a relatively simple task that can be completed in about an hour. However, it is important to follow the steps carefully to avoid damaging the faucet or the sink.

If you are not comfortable working with plumbing, you may want to consider hiring a professional to do the job for you.

How to Change a Faucet in a Bathtub

Q: What tools do I need to change a faucet?

A: You will need the following tools:

  • A wrench
  • A screwdriver
  • A pair of pliers
  • A bucket
  • A rag
  • Plumbing tape

Q: How do I remove the old faucet?

A: 1. Turn off the water supply to the faucet.
2. Disconnect the water supply lines from the faucet.
3. Remove the screws that hold the faucet to the sink.
4. Pull the faucet away from the sink.
5. Disconnect the drain hose from the faucet.

Q: How do I install the new faucet?

A: 1. Apply plumbing tape to the threads of the new faucet.
2. Insert the faucet into the sink.
3. Secure the faucet to the sink with the screws.
4. Connect the water supply lines to the faucet.
5. Turn on the water supply to the faucet.

Q: What if the faucet is stuck?

A: If the faucet is stuck, you can try using a penetrating oil to loosen the threads. You can also try using a heat gun to heat up the faucet. If the faucet is still stuck, you may need to call a plumber.

Q: What if I have a leak under the sink?

A: If you have a leak under the sink, it is likely caused by a faulty faucet. You can try tightening the screws on the faucet to stop the leak. If that does not work, you may need to replace the faucet.

Q: How do I prevent future leaks?

You can prevent future leaks by:

  • Installing a high-quality faucet.
  • Tightening the screws on the faucet regularly.
  • Replacing the faucet as soon as it starts to leak.

By following these tips, you can keep your faucets in good working order and prevent leaks.

Changing a bathtub faucet is a relatively simple task that can be completed in a few hours. By following the steps in this guide, you can save yourself time and money by doing it yourself.

Here are the key takeaways from this article:

  • Before you begin, make sure you have the necessary tools and materials.
  • Turn off the water supply to the faucet and drain the water from the bathtub.
  • Remove the old faucet by unscrewing the mounting screws and nuts.
  • Install the new faucet by following the manufacturer’s instructions.
  • Turn on the water supply and test the faucet to make sure it is working properly.

By following these steps, you can easily change a bathtub faucet and enjoy a new, working faucet in no time.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.