How to Replace a Tub and Shower Faucet | Step-by-Step Guide

How to Change a Tub Shower Faucet

Your tub shower faucet is one of the most important fixtures in your bathroom. It’s what you use to get clean, so it’s important that it’s working properly. If your faucet is leaking or dripping, or if it’s just not turning on or off properly, it’s time to replace it.

Changing a tub shower faucet is a relatively simple DIY project that can be completed in a few hours. In this article, we’ll walk you through the steps of how to change a tub shower faucet, from start to finish. We’ll provide detailed instructions and photos, so you can be confident that you’re doing the job correctly.

So if your tub shower faucet is giving you trouble, read on to learn how to change it!

Step	Instructions	Image
1	Turn off the water supply to the faucet.
2	Remove the old faucet by unscrewing the nuts that hold it in place.
3	Install the new faucet by screwing it into place.
4	Turn on the water supply to the faucet and test it to make sure it is working properly.

A tub shower faucet is a type of faucet that is used to control the flow of water to a bathtub and shower. It typically consists of two valves, one for hot water and one for cold water, and a spout that controls the flow of water from the faucet. Tub shower faucets can be either single-handle or double-handle, and they can be either cartridge or stem-type.

This guide will show you how to change a tub shower faucet. We will cover the steps involved in removing the old faucet, installing the new faucet, and testing the new faucet to make sure it is working properly.

Gather your tools and materials

To change a tub shower faucet, you will need the following tools and materials:

• Adjustable wrench
• Pliers
• Tape measure
• Combination/socket wrench
• Penetrating oil
• New faucet
• New washers and O-rings
• Plumbing putty
• Caulk

Turn off the water supply to the faucet

Before you can begin removing the old faucet, you will need to turn off the water supply to the faucet. This will prevent any water from leaking out of the faucet while you are working on it.

To turn off the water supply to the faucet, locate the shut-off valves for the hot and cold water supplies to the faucet. These valves are typically located behind the faucet, near the wall. Turn the valves clockwise to turn off the water.

Remove the old faucet

Once the water supply to the faucet has been turned off, you can begin removing the old faucet.

1. First, use the adjustable wrench to loosen the nuts that are holding the faucet in place. These nuts are typically located on the back of the faucet, near the wall.
2. Once the nuts have been loosened, use the pliers to pry the faucet off of the wall. Be careful not to damage the pipes behind the faucet.
3. If the faucet is stuck, you may need to use a penetrating oil to loosen it. Apply the penetrating oil to the threads of the faucet and let it sit for a few minutes. Then, try to pry the faucet off of the wall again.

Install the new faucet

Once the old faucet has been removed, you can install the new faucet.

1. First, apply a small amount of plumber’s putty to the threads of the new faucet. This will help to seal the faucet to the wall and prevent leaks.
2. Then, hold the new faucet in place and tighten the nuts that are holding it in place. Be careful not to overtighten the nuts, as this could damage the faucet.
3. Once the nuts have been tightened, turn on the water supply to the faucet and test it to make sure it is working properly.

Test the new faucet

Once the new faucet has been installed, turn on the water supply to the faucet and test it to make sure it is working properly.

1. Turn on the hot and cold water valves to the faucet.
2. Make sure that the water is flowing smoothly from the faucet.
3. Check for any leaks around the faucet.

If the faucet is working properly, you have successfully completed the replacement process.

Replacing a tub shower faucet is a relatively simple task that can be completed by most homeowners. By following the steps in this guide, you can easily and safely replace your old faucet with a new one.

How to Change a Tub Shower Faucet?

Changing a tub shower faucet is a relatively simple DIY project that can be completed in about an hour. However, it is important to follow the steps carefully to ensure that the new faucet is installed correctly and that you do not damage the existing plumbing.

Tools and Materials

To change a tub shower faucet, you will need the following tools and materials:

• Adjustable wrench
• Channel-lock pliers
• Combination/socket wrench
• Hacksaw
• Plumber’s putty
• Penetrating oil
• Replacement tub shower faucet
• Tape measure
• Tub drain plug
• Work gloves

Step 1: Turn off the water supply

The first step is to turn off the water supply to the faucet. This can usually be done by turning the shut-off valves located behind the faucet. If you are unable to find the shut-off valves, you can turn off the main water supply to the house.

Step 2: Remove the old faucet

Once the water supply has been turned off, you can begin to remove the old faucet. To do this, you will need to loosen the nuts or screws that hold the faucet to the wall or tub. These nuts or screws are typically located behind the faucet handle or on the bottom of the faucet.

Once the nuts or screws have been loosened, you can remove the faucet by pulling it straight out. Be careful not to damage the surrounding plumbing.

Step 3: Discard the old faucet

Once the old faucet has been removed, you can discard it. Be sure to dispose of the old faucet in a way that is environmentally friendly.

Step 4: Install the new faucet

To install the new faucet, you will need to apply a thin layer of plumber’s putty to the threads of the new faucet. This will help to create a watertight seal.

Next, insert the faucet into the hole in the wall or tub. Be sure that the faucet is aligned correctly.

Once the faucet is inserted, you can hand-tighten the nuts or screws that hold the faucet in place. Then, use a wrench to tighten the nuts or screws until they are snug.

Step 5: Turn on the water supply

Once the new faucet has been installed, you can turn on the water supply. Be sure to check for leaks around the faucet. If you find any leaks, you can tighten the nuts or screws until the leaks stop.

Changing a tub shower faucet is a relatively simple DIY project that can be completed in about an hour. By following these steps, you can easily replace your old faucet with a new one that will provide you with years of trouble-free use.

Here are some additional tips for changing a tub shower faucet:

• If you are not comfortable working with plumbing, you may want to hire a professional to do the job for you.
• Be sure to use the correct tools and materials for the job.
• Take your time and follow the steps carefully.
• If you encounter any problems, do not hesitate to ask for help.

  How do I remove a tub shower faucet?

1. Turn off the water supply to the faucet. This is usually located at the main water shut-off valve for your home.
2. Remove the faucet handles. There are usually two screws on the back of each handle. Use a screwdriver to loosen these screws and remove the handles.
3. Disconnect the water supply lines. There will be two water supply lines connected to the back of the faucet. Use a wrench to loosen the nuts that connect these lines to the faucet and disconnect them.
4. Remove the faucet body. There will be two bolts that hold the faucet body to the wall. Use a wrench to loosen these bolts and remove the faucet body.
5. Install the new faucet. Reverse the steps above to install the new faucet. Make sure to tighten all of the connections securely.

What tools do I need to change a tub shower faucet?

You will need the following tools to change a tub shower faucet:

• A screwdriver
• A wrench
• A pair of pliers
• A bucket
• A new faucet

How long does it take to change a tub shower faucet?

The amount of time it takes to change a tub shower faucet will vary depending on the type of faucet you have and your skill level. Generally, the process should take about 30 minutes to an hour.

What is the most common mistake people make when changing a tub shower faucet?

The most common mistake people make when changing a tub shower faucet is not turning off the water supply to the faucet. This can result in water damage to your home.

Can I change a tub shower faucet myself?

Yes, you can change a tub shower faucet yourself. However, it is important to be careful and follow the instructions carefully. If you are not comfortable doing this type of work, you may want to hire a professional plumber.

What are the benefits of changing a tub shower faucet?

There are several benefits to changing a tub shower faucet, including:

• Improved water flow: A new faucet can improve the water flow to your shower, making it more comfortable to use.
• Increased water pressure: A new faucet can also increase the water pressure to your shower, making it more powerful.
• Longer lifespan: A new faucet will last longer than an old faucet, saving you money in the long run.
• Improved appearance: A new faucet can improve the appearance of your bathroom, making it more stylish and inviting.

How much does it cost to change a tub shower faucet?

The cost of changing a tub shower faucet will vary depending on the type of faucet you choose and the cost of labor. Generally, the cost of a new faucet will range from $50 to $200. The cost of labor will vary depending on the complexity of the installation.

What are the different types of tub shower faucets?

There are several different types of tub shower faucets available, including:

• Single-handle faucets: These faucets have a single handle that controls both the hot and cold water.
• Two-handle faucets: These faucets have two separate handles, one for the hot water and one for the cold water.
• Thermostatic faucets: These faucets automatically adjust the water temperature to a preset level.
• Pressure-balanced faucets: These faucets maintain a constant water pressure even when the water flow is reduced.

Which type of tub shower faucet is best for me?

The best type of tub shower faucet for you will depend on your personal preferences and needs. If you are looking for a simple and affordable option, a single-handle faucet may be a good choice. If you want more control over the water temperature, a two-handle faucet or a thermostatic faucet may be a better option. If you are concerned about water pressure, a pressure-balanced faucet may be a good choice.

Changing a tub shower faucet is a relatively simple task that can be completed in a few hours. By following the steps in this guide, you can save yourself time and money by doing it yourself.

Here are the key takeaways from this article:

• Before you begin, make sure you have the right tools and materials.
• Turn off the water supply to the faucet and drain the water from the pipes.
• Remove the old faucet by unscrewing the nuts that hold it in place.
• Install the new faucet by following the instructions that came with it.
• Turn on the water supply and test the faucet to make sure it is working properly.

By following these steps, you can easily change a tub shower faucet and get your bathroom back in working order.