How Do You Measure A Toilet Seat?

AvatarByLiana Farrell Toilet Queries

How Do You Measure a Toilet Seat?

A toilet seat is a relatively simple object, but it’s important to get the right measurements when you’re shopping for a new one. After all, you don’t want to end up with a seat that’s too big or too small for your toilet.

In this article, we’ll walk you through the process of measuring your toilet seat so that you can find the perfect replacement. We’ll also provide some tips on how to choose the right seat for your needs.

So whether you’re looking for a new seat for your old toilet or you’re building a new bathroom from scratch, read on for all the information you need to know about measuring a toilet seat.

Step Instructions Image
1 Remove the old toilet seat.
2 Measure the distance between the two mounting bolts on the toilet bowl.
3 Select a new toilet seat that is the same width as the old seat and has mounting holes that are the same distance apart.

How Do You Measure A Toilet Seat?

Measuring a toilet seat is a simple task that can be completed in a few minutes. However, it is important to get the measurements correct in order to ensure that you order the correct replacement seat.

This guide will walk you through the steps of measuring a toilet seat, including the tools and materials you will need, as well as the steps to take.

Tools and Materials Needed

To measure a toilet seat, you will need the following tools and materials:

  • Tape measure
  • Pencil
  • Paper
  • Toilet seat

Steps to Measure a Toilet Seat

To measure a toilet seat, follow these steps:

1. Remove the old toilet seat. If you are replacing an existing toilet seat, you will need to remove it first. To do this, locate the two bolts that hold the seat to the toilet bowl. Use a screwdriver to loosen the bolts and remove the seat.
2. Measure the width of the toilet bowl. The width of the toilet bowl is the distance between the two bolts that hold the seat. Use a tape measure to measure the width of the toilet bowl.
3. Measure the length of the toilet bowl. The length of the toilet bowl is the distance from the front of the bowl to the back of the bowl. Use a tape measure to measure the length of the toilet bowl.
4. Measure the height of the toilet seat. The height of the toilet seat is the distance from the top of the seat to the bottom of the seat. Use a tape measure to measure the height of the toilet seat.
5. Record your measurements. Once you have measured the width, length, and height of the toilet bowl, record your measurements. You will need these measurements to order a replacement toilet seat.

Measuring a toilet seat is a simple task that can be completed in a few minutes. By following the steps in this guide, you can ensure that you order the correct replacement seat for your toilet.

Here are some additional tips for measuring a toilet seat:

  • If you are unsure of how to measure your toilet seat, you can always consult with a plumber or a hardware store clerk.
  • When ordering a replacement toilet seat, be sure to provide the manufacturer’s name, model number, and the measurements of your toilet bowl.
  • Make sure to install the new toilet seat correctly. If you are not comfortable doing this yourself, you can always hire a plumber to do it for you.

How Do You Measure A Toilet Seat?

Measuring a toilet seat is a relatively simple task, but it’s important to get the measurements correct so that you order the right replacement seat. The following steps will walk you through the process of measuring your toilet seat:

1. Locate the toilet seat bolts. The toilet seat bolts are located on the underside of the toilet seat. They are typically two bolts, one on each side of the toilet seat.
2. Measure the distance between the toilet seat bolts. Use a tape measure to measure the distance between the center of the two toilet seat bolts. This measurement will be the width of your new toilet seat.
3. Measure the length of the toilet seat. Use a tape measure to measure the length of the toilet seat from the front to the back. This measurement will be the length of your new toilet seat.
4. Add 1/2 inch to each measurement. This will allow for a little bit of wiggle room when you install the new toilet seat.

Once you have measured your toilet seat, you can order a new seat that is the correct size. Be sure to check the manufacturer’s website for specific instructions on how to measure your toilet seat.

Remove the Old Toilet Seat

Before you can install a new toilet seat, you need to remove the old seat. This is a relatively simple task, but it’s important to follow the steps carefully to avoid damaging the toilet.

1. Turn off the water supply to the toilet. The water supply valve is typically located on the wall behind the toilet. Turn the valve clockwise to turn off the water supply.
2. Flush the toilet to drain the water from the tank. This will make it easier to remove the toilet seat.
3. Locate the toilet seat bolts. The toilet seat bolts are located on the underside of the toilet seat. They are typically two bolts, one on each side of the toilet seat.
4. Loosen the toilet seat bolts. Use a screwdriver to loosen the toilet seat bolts. Be careful not to over-tighten the bolts, as this could damage the toilet seat.
5. Lift up on the toilet seat. Once the bolts are loosened, you can lift up on the toilet seat and remove it from the toilet.

Place the Toilet Seat on a Flat Surface

Before you install the new toilet seat, you need to place it on a flat surface. This will make it easier to align the seat with the toilet bowl.

1. Place the toilet seat on a table or other flat surface. Make sure that the toilet seat is level and that the bolts are facing up.
2. Align the toilet seat with the toilet bowl. The toilet seat should be centered on the toilet bowl. The front of the toilet seat should be about 1 inch from the front of the toilet bowl.
3. Mark the location of the toilet seat bolts. Use a pencil to mark the location of the toilet seat bolts on the toilet bowl.

Measuring and installing a toilet seat is a relatively simple task, but it’s important to follow the steps carefully to avoid damaging the toilet. By following the steps in this guide, you can easily replace your old toilet seat with a new one.

How do I measure a toilet seat?

To measure a toilet seat, you will need a tape measure and a pencil.

1. Locate the bolts that hold the toilet seat to the toilet bowl. These bolts are typically located on the back of the toilet seat, near the hinge.
2. Measure the distance between the center of the two bolts. This is the width of your toilet seat.
3. Measure the length of the toilet seat from the front to the back. This is the length of your toilet seat.
4. Record your measurements. You will need these measurements when you purchase a new toilet seat.

What if my toilet seat is too big or too small?

If your toilet seat is too big or too small, you can either purchase a new toilet seat that fits your toilet, or you can modify the existing toilet seat to make it fit.

To modify a toilet seat, you will need a hacksaw, a file, and sandpaper.

1. Remove the toilet seat from the toilet bowl. To do this, you will need to loosen the bolts that hold the toilet seat to the toilet bowl.
2. Use a hacksaw to cut the toilet seat to the desired size. Be careful not to cut the toilet bowl.
3. Use a file and sandpaper to smooth the edges of the toilet seat. This will prevent the toilet seat from scratching your toilet bowl.
4. Reattach the toilet seat to the toilet bowl. To do this, you will need to tighten the bolts that hold the toilet seat to the toilet bowl.

What are the different types of toilet seats?

There are two main types of toilet seats: standard and elongated. Standard toilet seats are 17 inches long, while elongated toilet seats are 19 inches long. Standard toilet seats are typically used on round toilets, while elongated toilet seats are typically used on elongated toilets.

There are also a variety of other features that you can find on toilet seats, such as:

  • Soft close hinges
  • Quick release hinges
  • Heated seats
  • Bidets

How do I install a toilet seat?

To install a toilet seat, you will need a Phillips head screwdriver and a wrench.

1. Remove the old toilet seat. To do this, you will need to loosen the bolts that hold the toilet seat to the toilet bowl.
2. Place the new toilet seat on the toilet bowl. Make sure that the holes in the toilet seat align with the bolts in the toilet bowl.
3. Secure the toilet seat to the toilet bowl. To do this, you will need to tighten the bolts that hold the toilet seat to the toilet bowl.
4. Test the toilet seat to make sure that it is installed properly. You should be able to sit on the toilet seat without it moving.

In this article, we have discussed how to measure a toilet seat. We have covered the different types of toilet seats, the parts of a toilet seat, and the steps involved in measuring a toilet seat. We have also provided a few tips and tricks to help you get the most accurate measurement.

We hope that this article has been helpful. If you have any further questions, please do not hesitate to contact us.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.