How to Remove a Tub Faucet (Step-by-Step Guide)

AvatarByLiana Farrell Faucet Queries

How to Take Off a Tub Faucet

Your tub faucet is one of the most important fixtures in your bathroom, but it’s also one of the most likely to break down. If your faucet is leaking, dripping, or not turning on at all, you may need to take it off and replace it.

Taking off a tub faucet is a relatively simple task, but it does require some basic tools and know-how. In this article, we’ll walk you through the process of removing a tub faucet, step-by-step. We’ll also provide some tips on how to choose the right replacement faucet for your bathroom.

So if your tub faucet is giving you trouble, read on for everything you need to know about how to take it off.

Step Instructions Image
1 Turn off the water supply to the faucet.
2 Remove the decorative cap from the faucet handle.
3 Loosen the set screws on the faucet handle with a screwdriver.
4 Remove the faucet handle.
5 Unscrew the faucet stem from the faucet body.
6 Remove the faucet body from the sink.

This tutorial will show you how to remove a tub faucet. This is a relatively simple task that can be completed in about 30 minutes. However, it is important to follow the steps carefully to avoid damaging the faucet or the plumbing.

Gather your tools and materials

To remove a tub faucet, you will need the following tools and materials:

  • Adjustable wrench
  • Pliers
  • Penetrating oil
  • Rags
  • Replacement faucet
  • Plumbing tape

Turn off the water supply

The first step is to turn off the water supply to the faucet. This will prevent any water from spilling out when you remove the faucet.

To do this, find the shutoff valve for the faucet. This is usually located near the base of the faucet, on the hot and cold water supply lines. Turn the valve clockwise to turn off the water.

Loosen the faucet handles

The next step is to loosen the faucet handles. These are usually held in place by screws or clips.

To loosen the screws, use a Phillips head screwdriver. To loosen the clips, use a pair of pliers.

Remove the faucet body

Once the faucet handles are loose, you can remove the faucet body. The faucet body is the part of the faucet that connects to the water supply lines.

To remove the faucet body, you will need to use an adjustable wrench. Place the wrench on the nut at the base of the faucet body and turn it counterclockwise to loosen it.

Once the nut is loose, you can pull the faucet body straight out of the sink.

Remove the escutcheon

The escutcheon is the decorative cover that surrounds the faucet body. To remove the escutcheon, you will need to use a flathead screwdriver.

Place the screwdriver under the escutcheon and pry it up. Once the escutcheon is loose, you can pull it straight out.

Remove the old faucet gasket

The old faucet gasket is a rubber ring that seals the faucet to the sink. To remove the old gasket, you will need to use a putty knife.

Place the putty knife under the gasket and pry it up. Once the gasket is loose, you can pull it straight out.

Install the new faucet gasket

The new faucet gasket is a rubber ring that seals the faucet to the sink. To install the new gasket, you will need to use a putty knife.

Place the gasket on the faucet body and press it down firmly. Make sure that the gasket is properly seated in the groove.

Install the new faucet body

To install the new faucet body, you will need to use an adjustable wrench. Place the wrench on the nut at the base of the faucet body and turn it clockwise to tighten it.

Once the nut is tight, you can replace the faucet handles.

Turn on the water supply

The final step is to turn on the water supply to the faucet. This will test the faucet to make sure that it is working properly.

To do this, turn the shutoff valve clockwise to turn on the water.

Check the faucet for leaks. If there are no leaks, you have successfully removed and replaced a tub faucet.

Removing and replacing a tub faucet is a relatively simple task that can be completed in about 30 minutes. However, it is important to follow the steps carefully to avoid damaging the faucet or the plumbing.

If you are not comfortable doing this yourself, you can always hire a professional plumber to do the job for you.

How to Take Off a Tub Faucet

Removing a tub faucet is a relatively simple task that can be completed in a few minutes. However, it is important to follow the steps carefully to avoid damaging the faucet or the sink.

Tools and Materials

To remove a tub faucet, you will need the following tools and materials:

  • Adjustable wrench
  • Pliers
  • Penetrating oil
  • Rags
  • Tape measure
  • Screwdriver

Steps

1. Turn off the water supply to the faucet.
2. Disconnect the water lines from the faucet.
3. Loosen the faucet nuts.
4. Remove the faucet.
5. Install the new faucet.

Turn Off the Water Supply to the Faucet

The first step is to turn off the water supply to the faucet. This can be done by turning the shut-off valves located behind the faucet.

Disconnect the Water Lines from the Faucet

Once the water supply to the faucet is turned off, you can disconnect the water lines from the faucet. The water lines are typically located behind the faucet and are connected to the faucet with a set of compression fittings. To disconnect the water lines, you will need to loosen the compression nuts on each fitting.

Loosen the Faucet Nuts

The next step is to loosen the faucet nuts. The faucet nuts are located on the underside of the faucet and are typically held in place with a set of lock washers. To loosen the faucet nuts, you will need to use an adjustable wrench.

Remove the Faucet

Once the faucet nuts are loose, you can remove the faucet. To do this, you will need to pull the faucet straight up and off of the sink.

Install the New Faucet

To install the new faucet, you will need to reverse the steps above. First, you will need to install the new faucet on the sink. Then, you will need to connect the water lines to the faucet. Finally, you will need to turn on the water supply to the faucet.

Removing a tub faucet is a relatively simple task that can be completed in a few minutes. However, it is important to follow the steps carefully to avoid damaging the faucet or the sink. By following the steps outlined in this guide, you can easily remove your old tub faucet and install a new one.

How do I take off a tub faucet?

1. Turn off the water supply to the faucet. There will be a shut-off valve located behind the faucet or under the sink. Turn the valve clockwise until it is completely closed.
2. Remove the decorative cap. The cap is typically located at the base of the faucet and is held in place by a small screw. Use a screwdriver to remove the screw and lift off the cap.
3. Loosen the faucet nuts. There will be two nuts located on the underside of the faucet. Use a wrench to loosen the nuts until they are just barely tight enough to keep the faucet in place.
4. Pull the faucet off. Grab the faucet by the base and pull straight up. The faucet should come off with some resistance.
5. Clean the faucet threads. Use a rag or paper towel to clean the threads on the faucet and the sink. This will help to ensure that the new faucet seals properly.
6. Install the new faucet. Apply a thin coat of plumber’s putty to the threads of the new faucet. This will help to create a watertight seal. Insert the faucet into the sink and tighten the nuts until they are snug.
7. Turn on the water supply to the faucet. Make sure that the faucet is turned on all the way. Check for leaks around the faucet. If there are any leaks, tighten the nuts until the leak stops.

What tools do I need to take off a tub faucet?

You will need the following tools to take off a tub faucet:

  • A screwdriver
  • A wrench
  • A rag or paper towel
  • A thin coat of plumber’s putty

What if the faucet is stuck?

If the faucet is stuck, you can try the following:

1. Apply a penetrating oil to the threads of the faucet. Let the oil sit for a few minutes and then try to loosen the nuts again.
2. Use a heat gun or hair dryer to heat up the faucet. This will help to loosen the nuts.
3. Use a hammer and chisel to gently tap on the nuts. This will help to break them loose.

If you are unable to remove the faucet yourself, you can call a plumber for help.

What if I break the faucet while I’m taking it off?

If you break the faucet while you’re taking it off, you will need to replace the faucet. You can purchase a new faucet at your local hardware store.

How do I install a new tub faucet?

To install a new tub faucet, follow these steps:

1. Turn off the water supply to the faucet. There will be a shut-off valve located behind the faucet or under the sink. Turn the valve clockwise until it is completely closed.
2. Remove the old faucet. Follow the steps above to remove the old faucet.
3. Clean the faucet threads. Use a rag or paper towel to clean the threads on the faucet and the sink. This will help to ensure that the new faucet seals properly.
4. Apply a thin coat of plumber’s putty to the threads of the new faucet. This will help to create a watertight seal.
5. Insert the new faucet into the sink and tighten the nuts until they are snug. Make sure that the faucet is turned on all the way. Check for leaks around the faucet. If there are any leaks, tighten the nuts until the leak stops.
6. Turn on the water supply to the faucet. Make sure that the faucet is turned on all the way. Check for leaks around the faucet. If there are any leaks, tighten the nuts until the leak stops.

In this tutorial, we have shown you how to take off a tub faucet. We hope that you found this information helpful and that you were able to successfully remove your faucet.

Here are the key takeaways from this tutorial:

  • Before you begin, make sure that you have the necessary tools and materials.
  • Turn off the water supply to the faucet.
  • Loosen the nuts and bolts that hold the faucet in place.
  • Remove the faucet from the sink.
  • Clean the area where the faucet was installed.
  • Reinstall the new faucet.

We encourage you to practice this process on a spare faucet before attempting it on your main faucet. This will help you to become familiar with the steps involved and to ensure that you do not damage your existing faucet.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.