How To Get Water Out Of Toilet Bowl When Replacing?

AvatarByLiana Farrell Toilet Queries

How to Get Water Out of a Toilet Bowl When Replacing a Toilet

Replacing a toilet is a relatively straightforward task, but it can be tricky to get the water out of the bowl first. If you don’t properly drain the water, you could end up making a mess or even damaging your new toilet.

In this article, we’ll show you how to quickly and easily drain the water from a toilet bowl so that you can replace it with a new one. We’ll also provide some tips on how to avoid common mistakes during the replacement process.

So if you’re thinking about replacing your toilet, read on for all the information you need to know!

Step Instructions Image
1 Turn off the water supply to the toilet.
2 Flush the toilet to drain as much water as possible.
3 Use a plunger to remove any remaining water.
4 Use a wet/dry vacuum to remove any remaining water or debris.

How to Get Water Out of Toilet Bowl When Replacing?

Turn Off the Water Supply

The first step to replacing a toilet is to turn off the water supply. This will prevent any water from flowing into the toilet bowl and making a mess. To do this, locate the water supply valve located on the wall behind the toilet. It will be a small, round valve with a handle. Turn the handle clockwise to turn off the water supply.

Remove the Toilet Seat

The next step is to remove the toilet seat. There are two bolts located on the back of the toilet seat that hold it in place. Use a screwdriver to loosen these bolts and remove the seat.

How to Remove a Toilet Seat with Clips

Some toilet seats are held in place with clips instead of bolts. To remove a toilet seat with clips, locate the clips on the back of the seat. They will be small, metal pieces that are attached to the seat with screws. Use a screwdriver to loosen the screws and remove the clips.

How to Remove a Toilet Seat with a Bolt and Wing Nut

Other toilet seats are held in place with a bolt and wing nut. To remove a toilet seat with a bolt and wing nut, locate the bolt on the back of the seat. It will be a small, round bolt with a wing nut on top. Use a wrench to loosen the wing nut and remove the bolt.

How to Remove a Toilet Seat with a Button

Some toilet seats are held in place with a button. To remove a toilet seat with a button, locate the button on the back of the seat. It will be a small, round button that is pressed in to release the seat. Press the button and lift up on the seat to remove it.

Once the toilet seat is removed, you will be able to see the water in the toilet bowl. You can now proceed to remove the water from the bowl.

Remove the Water from the Toilet Bowl

There are a few different ways to remove the water from the toilet bowl.

Use a Shop Vac

One way to remove the water from the toilet bowl is to use a shop vac. Place the end of the shop vac hose into the toilet bowl and turn on the vacuum. The vacuum will suck up the water from the bowl.

Use a Bucket and Sponge

Another way to remove the water from the toilet bowl is to use a bucket and sponge. Place a bucket under the toilet bowl and pour some water into the bowl. Use the sponge to soak up the water and pour it into the bucket. Repeat this process until all of the water has been removed from the bowl.

Use a Plunger

You can also use a plunger to remove the water from the toilet bowl. Place the plunger over the drain hole in the bottom of the bowl and push down on the plunger. The plunger will create a vacuum that will suck up the water from the bowl. Repeat this process until all of the water has been removed from the bowl.

Once the water has been removed from the toilet bowl, you can proceed to replace the toilet seat.

Replace the Toilet Seat

To replace the toilet seat, simply reverse the steps you took to remove it. First, attach the toilet seat to the toilet bowl using the bolts or clips. Then, replace the toilet seat cover.

Replacing a toilet seat is a relatively simple task that can be completed in a few minutes. By following these steps, you can easily remove the water from the toilet bowl and replace the toilet seat.

Disconnect the Water Supply Line

Before you can remove the toilet, you need to disconnect the water supply line. This is a simple process, but it is important to do it correctly to avoid flooding your bathroom.

1. Turn off the water supply to the toilet. This is usually located at the back of the toilet, near the floor. There will be a small valve that you can turn to the off position.
2. Flush the toilet to drain any remaining water from the tank.
3. Locate the water supply line. This is a flexible hose that connects the toilet to the water supply. It is usually located at the bottom of the toilet tank.
4. Use a pair of pliers to loosen the nut that connects the water supply line to the toilet.
5. Pull the water supply line off of the toilet. Be careful not to spill any water.

Once the water supply line is disconnected, you can remove the toilet.

Drain the Water from the Bowl

The next step is to drain the water from the toilet bowl. This can be done by using a plunger or a wet/dry vacuum.

1. If you are using a plunger, place the cup of the plunger over the drain hole in the bottom of the toilet bowl.
2. Push down on the plunger and pull up quickly. Repeat this process several times until all of the water has been drained from the bowl.
3. If you are using a wet/dry vacuum, place the hose of the vacuum over the drain hole in the bottom of the toilet bowl.
4. Turn on the vacuum and suck up all of the water from the bowl.

Once the water has been drained from the bowl, you can remove the toilet.

Removing a toilet is a relatively simple task, but it is important to follow the steps carefully to avoid any damage to your plumbing. By following the steps in this guide, you can safely remove your toilet and replace it with a new one.

How do I get the water out of the toilet bowl when replacing the toilet?

There are a few different ways to get the water out of the toilet bowl when replacing the toilet. You can:

  • Use a plunger to push the water out of the bowl.
  • Use a wet/dry vacuum to suck the water out of the bowl.
  • Use a bucket and a sponge to scoop the water out of the bowl.
  • Turn off the water supply to the toilet and flush the toilet to drain the water from the bowl.

Once the water is out of the bowl, you can proceed with replacing the toilet.

What if the water is too high to reach with a plunger or vacuum?

If the water is too high to reach with a plunger or vacuum, you can turn off the water supply to the toilet and flush the toilet to drain the water from the bowl. Once the water is drained, you can use a bucket and a sponge to scoop the remaining water out of the bowl.

What if I don’t have a plunger or vacuum?

If you don’t have a plunger or vacuum, you can use a bucket and a sponge to scoop the water out of the bowl. You can also try using a wet/dry vacuum to suck the water out of the bowl.

What if I turn off the water supply to the toilet and flush it, but the water doesn’t drain?

If you turn off the water supply to the toilet and flush it, but the water doesn’t drain, there may be a clog in the toilet drain. You can try using a plunger to clear the clog. If that doesn’t work, you may need to call a plumber to fix the clog.

How do I prevent water from getting into the toilet bowl when replacing the toilet?

To prevent water from getting into the toilet bowl when replacing the toilet, you can:

  • Turn off the water supply to the toilet before you start.
  • Place a bucket under the toilet to catch any water that leaks out.
  • Use a sealant around the base of the toilet to prevent water from seeping in.

By following these tips, you can help to prevent water from getting into the toilet bowl when replacing the toilet.

In this article, we have discussed how to get water out of a toilet bowl when replacing it. We have covered a variety of methods, including using a plunger, a wet/dry vacuum, and a bucket and towels. We have also provided tips on how to prevent water from overflowing the bowl in the first place.

We hope that this article has been helpful. If you have any other questions, please do not hesitate to contact us.

Author Profile

Liana Farrell
Liana Farrell
Liana Farrell is the owner of toiletty.com. She is a mom of two and is very passionate about home improvement.

Liana has ten years of home improvement experience, and in her own words, she said: “I love improving the home, and I’m very passionate about keeping the home in the best possible condition. I love it!”

Liana Farrell balances beauty and functionality when she goes about her home improvement jobs.